8B-34 AIR BAG SYSTEM
Warning:
When placing a live air bag (inflator) module on bench or
other surface, always face the bag up, away from the
surface. As the live passenger air bag (inflator) module
must be placed with its bag (trim cover) facing up, place it
on the workbench with a slit (1) or use the workbench vise
(2) to hold it securely at its lower mounting bracket (3). It is
also prohibited to place anything on top of the trim cover
and stack air bag (inflator) modules.This is necessary so
that a free space is provided to allow the air bag to expand
in the unlikely event of accidental deployment.
Otherwise, personal injury may result.
Live (Undeployed) Air Bag (Inflator) Module
Special care is necessary when handling and storing a live
(undeployed) airbag (inflator) module.
The rapid gas generation produced during deployment of the
air bag could cause the air bag (inflator) module, or an object
in front of the air bag (inflator) module, to be thrown through
the air in the unlikely event of an accidental deployment.
Warning:
Never attempt to measure the resistance of the air bag
(inflator) module. It is very dangerous as the electric
current from the tester may deploy theairbag.
•
Never attempt disassembly of the air bag (inflator) module.
If any abnormality is found, be sure to replace it with new
one as an assembly.
•
When an abnormality is noted as existing in the live
(undeployed) air bag (inflator) module, be sure to deploy it
before discarding it.
•
When grease, cleaning agent, oil, water, etc., got on the air
bag (inflator) module wipe it off immediately with a dry
cloth.
•
If air bag (inflator) module was dropped from a height of 90
cm (3 ft) or more, it should be replaced with a new one as
an assembly.
Warning:
•
For handling and storage of a live air bag (inflator)
module, select a place where the ambient temperature
below 65°C (150°F), without high humidity and away
from electric noise.
•
When carrying a live air bag (inflator) module, make
sure the bag opening is pointed away from you. In case
of an accidental deployment, the bag will then deploy
with minimal chance of injury. Never carry the air bag
(inflator) module by the wires or connector on the
underside of the module.
Otherwise, personal injury may result.
•
Summary of Contents for Zen Estilo 2018
