ENGINE GENERAL INFORMATION AND DIAGNOSIS 1A-17
9. Troubleshooting for DTC
Based on the DTC indicated in Step 6 or 7 and referring to the applicable DTC diag. flow table in Section 6E,
locate the cause of the trouble, namely in a sensor, switch, wire harness, connector, actuator, ECM or other
part and repair or replace faulty parts.
10. Check for Intermittent Proble
Check parts where an intermittent trouble is easy to occur (e.g., wire harness, connector, etc.), referring to
“INTERMITTENT AND POOR CONNECTION” in Section 0A and related circuit of DTC recorded in step 2.
11. Final Confirmation Test
Confirm that the problem symptom has gone and the engine is free from any abnormal conditions. If what
has been repaired is related to the DTC, clear the DTC once, perform DTC confirmation procedure and
confirm that no malfunction DTC (a normal code) is indicated.
Step
Action
Yes
No
1
Was "ENGINE DIAG. FLOW TABLE" performed ?
Go to Step 2.
Go to “ENGINE DIAG.
FLOW TABLE".
2
Check battery voltage.
Go to Step 3.
Charge or replace battery.
Is it 11 V or more ?
3
Is engine cranked ?
Go to Step 4.
Go to "DIAGNOSIS" in
section 1I.
4
Does engine start ?
Go to Step 5.
Go to Step 7.
5
Check engine idle speed /IAC duty referring to "Idle
Go to Step 6
Go to “ENGINE DIAGNOSIS
Speed/IAC Duty Inspection" in this section.
TABLE" in this section.
Is check result as specified?
6
Check ignition timing referring to "Ignition Timing
Go to "“ENGINE
Adjust ignition
Inspection" in section 1H.
DIAGNOSIS TABLE"
timing.
Is check result as specified?
in this section.
7
Check fuel supply as follows:
Go to Step 9.
Go to Step 8.
1) Check to make sure that enough fuel is filled is fuel
tank.
2) Turn the ignition switch ON position for 3 seconds and
then turn it OFF position.
Is fuel return pressure (returning sounds) felt from fuel
return hose when the ignition switch is turned ON position?
8
Check fuel pump for operating.
Go to "Diag. Flow
Go to "Diag. Flow
1) Was fuel pump operating sound heard form fuel filler
Table B-3" in this section
Table B-3" in this section.
for about 3 seconds after turning the ignition switch
ON position and stop?
9
Check ignition sperk referring to "Ignition Spark Test" in
Go to Step 10.
Go to "DIAGNOSIS"
section 1H.
in section 1H.
Is it in good condition?
10
Check fuel injector referring to "Fuel injector inspection"
Go to "ENGINE
Go to "Diag. Flow
in section 1G.
DIAGNOSIS TABLE"
Table B-2 in this section.
Is it in good condition?
in this section.
Engine Basic Inspection Flow Table
Summary of Contents for Zen Estilo 2018
