USER’S MANUAL
POWER OFFICE UPS
800/1000
SAVE THESE INSTRUCTIONS - This manual contains important safety, installation,
and operating instructions for the Power Office UPS 800/1000 that should be
followed during installation and maintenance of the UPS and batteries.
This UPS utilizes voltage that may be hazardous. Do not attempt to disassemble
the unit. The unit contains no user replaceable parts. Only factory service
personnel may perform repairs.
This pluggable type A equipment with battery already installed by the supplier
operator-installable and may be operated by laymen.
The mains socket outlet that supplies the UPS shall be installed near the UPS and
shall be easily accessible.
During the installation of the equipment, it should be assumed that the sum of the
leakage currents of the UPS and the connected loads do not exceed 3.5mA.
Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
Connection to any other type of receptacle other than a two-pole, three-wire
grounded receptacle may result in shock hazard as well as violate local electrical
codes.
In the event of an emergency, press the "OFF" button and disconnect the power
cord from the AC power supply to properly disable the UPS.
Do not allow any liquids or any foreign object to enter the UPS. Do not place
beverages or any other liquid-containing vessels on or near the unit.
This unit is intended for installation in a controlled environment (temperature
controlled, indoor area free of conductive contaminants). Avoid installing the UPS in
locations where there is standing or running water or excessive humidity.
Do not plug the UPS input into its own output.
Do not attach a power strip or surge suppressor to the UPS.
Do not attach non-computer-related items, such as medical equipment, life-support
equipment, microwave ovens, or vacuum cleaners to UPS.
To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and
avoid exposing the unit to direct sunlight or installing the unit near heat emitting
appliances such as space heater or furnaces.
Do not open or mutilate the battery or batteries. Released electrolytes harmful to
the skin and eyes and may be toxic.
Servicing of batteries should be performed or supervised by personnel
knowledgeable of batteries and the required precautions. Keep unauthorized
personnel away from batteries.
UPS
Mode
Status
On Battery LED On AC LED Fault LED
Sound
Battery normal.
Load normal.
Two (2) flashes
every 4 seconds.
Off
Two (2) beeps
every 8 seconds.
No load (for Green
mode function only.)
(Optional)
One flash every 4
seconds.
Off
One beep every
8 seconds.
UPS overload. UPS
will shut down at
120% of full load.
Two flashes
every other two
seconds.
Off
On
Continuous
beeping.
Over temperature.
Thirty-two flashes
every other
seconds.
Off
Sound emitted
depends on the
load situation.
UPS short-circuited.
Thirty-two flashes
every other
seconds.
Off
Thirty-two beeps
every other 2
seconds.
Over battery voltage
(for external
battery).
Eight flashes
every second.
Off
Eight beeps
every second.
Backup
Mode
In phase lock (AC
good, PLL working).
Off
Four flashes
every second.
Off
Off
Battery Full.
Off
Continuously
on.
Off
Off
Battery charge at
70%-90%.
Off
One flash
every 8
seconds.
Off
Off
Battery charge at
50%-70% load.
Off
One flash
every 4
seconds.
Off
Off
Battery charge at
30%-50% load.
Off
One flash
every 2
seconds.
Off
Off
Battery charge at
0%-30%.
Off
One flash
every second.
Off
Off
AC
Normal
Mode
UPS overload. UPS
will shut down at
120% of full load.
Off
Off
On
Continuous
beeping
Power off (UPS
completely off).
Off
Off
Off
Mode
AC normal and
battery is charging.
Off
One flash
every 2
seconds.
Off
UPS
Mode
Status
AVR LED
Low Battery
LED
Max. load LED
Sound
Ac Mode
When UPS in
AVR mold
On
N/A
Ac Mode 95% of Max Load
On
N/A
Battery
mode
1 min remain
(half load)
On
N/A
Battery Recycling Information
UPS contains non-spillable sealed lead-acid batteries. On the battery, you will find
the battery name. Please refer to the chart below for recycling information or contact
your local distributor for assistance.
*If any abnormal situations occur that are not listed above, please call for service immediately. When
calling for service, please have the following information read: 1) Model number and serial number; 2)
Date the problem occurred and date of purchase; 3) Full description of the problem, including load, LED,
and alarm statuses, installation conditions, working environments, etc.
MODEL
POF-800A
POF-1000A
CAPACITY
VA/W
800 VA / 400 W
1000 VA / 500 W
Voltage
110/115/120VAC or 220/230/240VAC
Voltage Range
86-144VAC or 154-280VAC
INPUT
Frequency
50/60Hz (Auto Sensing)
Frequency
Regulation
(Batt. Mode)
50Hz or 60Hz +/-1Hz
OUTPUT
Output Waveform
Simulated sine wave
Battery Type
12 V/ 7 AH x 1pc
12 V/ 9 AH x 1pc
Back up Time
Up to 20 minutes
Up to 30 minutes
BATTERY
Recharge Time
< 5 hours to 90% capacity
TRANSFER TIME
2-6ms (Typical)
AC Surge
Protection
175 Joules
Phone/Fax/
Modem Surge
Protection
RJ-11/45 (One In One Out)
AC Input
Circuit breaker
PROTECTION
Full Protection
Discharge, Overcharge and Overload Protection
Dimension
(DxWxH)
11.4 x 3.7 x 6.7 in.
PHYSICAL
Net Weight
11.1 lb
13.1 lb
Operating
Environment
0-40°C, 0-90 % Relative Humidity (non-condensing)
ENVIRONMENT
Noise Level
Less than 40dB
**Product specification may change without notice. Battery backup time is based on basic PC and
varies with equipment, configuration, battery age, temperature, etc.
Product Warranty and Service Information:
For U.S. customers, please register your product at www.MarusonUSA.com. For international customers,
please contact your local authorized distributor or e-mail [email protected] for assistance.
Maruson Technology Corporation
18557 E. GALE AVE.
,
CITY OF INDUSTRY, CA 91748
P.O. Box 1986, Walnut, CA 91788, USA
Toll Free: 1-888-MARUSON
TEL: +1-626-912-8388
FAX: +1-626-912-8680
E-mail: [email protected]
Web Site: www.MarusonUSA.com
701-0070925 IP-Maruson-POFUPS-02
Problem
Possible Cause
Solution
The UPS is not turned on.
Press and hold the Power button for at
least 2 seconds.
Low battery or battery voltage
less than 10V.
Charge the battery at least 8 hours.
LED display does not
turn on.
PCB failure.
PCB needs to be replaced. Call for
servicing information.
Power cord is loose.
Reconnect the power cord properly.
Circuit breaker tripped.
Reset the circuit breaker by pushing it
back in.
UPS is always in
Battery Mode.
PCB failure.
PCB needs to be replaced. Call for
servicing information.
The UPS is overload.
Remove some critical load.
Battery not fully charged.
Charge the UPS at least 8 hours.
When power fails,
back-up time is
shorter than normal.
Battery defect. It might be
due to high temperature
operation environment, or
improper operation to battery.
Replace the battery with the same type
of battery. Call for servicing information.
UPS beeps
continuously.
UPS is overloaded.
Remove some loads.
UPS Indicators & Controls
Specification
Safety Caution
UPS Indicators & Controls
Trouble Shooting
