background image

Resulting from an equal and opposite reaction to the cone's 

movement, strong bass causes all traditional subwoofer 

enclosures to generate acoustic vibrations. You feel this by 

touching the cabinet. Although the "physics" of this phe-

nomenon actually cause a subwoofer cabinet to resonate 

or even dance, most subwoofer designers apply weight or 

mass to the cabinet to minimize such disturbances, but still 

leave one by product—"smeared bass". Vibrations translated 

from the woofer to the cabinet actually dampen the bass 

signal causing a loose and "fuzzy" sound.

The Depth i integrates BalancedForce bass configuration 

to nullify cabinet vibrations. Originally engineered for the 

cost-no-object, state-of-the-art Statement™ E2 system, 

BalancedForce uses two or more drivers mounted at oppos-

ing angles. The Depth i's 3 drivers, spaced 120 degrees 

apart, operate in exact opposition, resulting in maximum 

cancellation delivering the ideal—pure bass energy with a 

reduction in cabinet contributions to the room as high as 

25dB over traditional subwoofer resonance solutions!

TriLinear™ Configuration

The use of three small, identical drivers maintains the low 

distortion levels and optimal control of an efficient and 

rigid small driver while moving the same amount of air as 

a driver three times larger. This allows powerful bass in a 

small package, free from the performance limitations of a  

heavy and hard to control single large driver.

Servo-Controlled Dynamic Drivers

 

All dynamic drivers generate distortion caused by spider 

and surround nonlinearities as well as voice coil inductive 

disturbances and variant motor strength during massive 

woofer excursions. These challenges plague all subwoofer 

designers. The result? Induced harmonic and intermodulated 

distortions causing dramatic disturbances at high excursions. 

This occurs significantly in almost all non-servo-controlled 

subwoofers.

MartinLogan’s advanced servo system uses a sophisticated 

monitoring and control circuit to detect and instantaneous-

ly correct any deviation between acoustical output and 

electrical input. The result? A reduction in distortion for 

the purest possible low-frequency reproduction.

Proprietary Switching Amplifier

 

The Depth i incorporates a proprietary switching ampli-

fier that allows for an incredible amount of woofer control 

resulting in tighter, better defined bass and while keeping 

distortion at the lowest possible levels.

25Hz Level Control

 

The Depth i 25Hz Level controls allows custom sound 

tailoring capabilities found in few subwoofers. A room, 

especially when small, can greatly exaggerate bass in the 

20–60Hz range. The Depth i’s 25Hz Level control knob 

increases or decreases lower bass to compensate for these 

room anomalies and allows increased deep bass if you 

desire a subsonic sense of energy at the lowest frequencies. 

20     MartinLogan Exclusives

m

artIn

l

ogan

 e

xClusIves

BalancedForce™ For Cleaner Bass

Summary of Contents for Depth I





























Reviews: