background image

20

E1300 TECHNICAL SPECIFICATION

INPUT IMPEDANCE

20K Ohms differential, 10K Ohms single ended

INPUT SENSITIVITY

Selectable 0.775mv (36dB gain) or 1.23V 
(32dB gain)

FREQUENCY RESPONSE

17Hz - 46KHz + 0dB – 3dB

POWER BANDWIDTH

10Hz - 40KHz + 0dB – 0.5dB

POWER OUTPUT

400 Watts Cont Av into 8 Ohms
720 Watts Cont Av into 4 Ohms
1000 Watts Cont Av into 2 Ohms
1440 Watts Cont Av bridged into 8 Ohms

OUTPUTS

Impedance

22m

DC offset

<2mV

SLEW RATE

70 Volts per micro second

( NOISE) / NOISE

>100dB 20Hz - 20KHz IEC, A weighted

RATIO

DISTORTION

< 0.06% @ 1dB below full power

POWER REQUIREMENTS

230V Setting

115V Setting

Operating voltage 

180* – 250Vac 

90* - 125Vac

Minimum start-up voltage

140Vac

70Vac

Peak inrush current

11.8 Amps

23 Amps

Current draw 4

Quiescent (No load)

0.9 Arms

1.8 Arms

1/8 Full power (Both channels) 4.8 Arms

9.6 Arms

1/3 Full power (Both channels) 7.2 Arms

14 Arms

Dual voltage operation 115V or 230V  
(internal Links). 

*Note: The amplifier will operate down to the indicated mains voltage but with
reduced power output.

AMBIENT TEMPERATURE

Maximum ambient operating tempe40°C

INDICATORS

Power On, Signal Level, Bridge, Thermal, 
Card/Module Enable

INPUT CONNECTIONS

2 x XLR with 2 x XLR parallel links 
Pin 2 Hot, Pin 3 Cold

Martin Audio – E1300 Amplifier

E

NGLISH

22

All material © 2007. Martin Audio Ltd. Subject to change without notice.

Summary of Contents for E1300


























Reviews: