Marti MGP-22, Assembly Instructions & User Manual

Page: 10 / 18

INSTRUCTIONS FOR LIGHTING BURNER:
OPERATING INSTRUCTIONS
1. Read all instructions before lighting.
2. Make sure all control knobs are in the OFF position.
3. When use 20lb. cylinder: Turn on the cylinder valve.
4. Select the burner to be lit. Push andturn the control knob of
that burner counter-clockwise to HIGH. Hold the control knob
pushed down for 2-3 seconds. It will light the burner.
5. Adjust the flame by turning control knob between HIGH and LOW.
6. Repeat step 4 for lighting other burner.
7. If ignition does not occur in 5 seconds, turn the burner control(s) OFF, wait 5 minutes, and
repeat the lighting procedure.
MANUAL LIGHTING
1. Make sure all control knobs are in the OFF position.
2. When use 20lb. cylinder: Turn on the cylinder valve.
3. Remove the cooking plate. Insert a match into the match lighter. Strike the match and place
near the gas outlet openings on the burner. Push and turn
the control knob of that burner counter-clockwise to HIGH.
Hold the control knob pushed down for 2-3 seconds.
It will light the burner.
4. Adjust the flame by turning control knob between HIGH and LOW.
5. Repeat step 3 for lighting other burner.
6. If ignition does not occur in 5 seconds, turn the burner control(s)
OFF, wait 5 minutes, and repeat the lighting procedure.
7. Place the cooking plate back onto the plancha body. Note: Match lighter is attached to the
main valve tube at the bottom of gas cooking plate by the manufacturer. Place the match
lighter on the platform of the control panel after use.
SHUT DOWN INSTRUCTIONS
1. Push and turn control knob clockwise to OFF position.
2. 20LB. cylinder: Turn LP cylinder gas valve clockwise to OFF position when plancha is not in
use. 1LB cylinder: Turn the cylinder counter-clockwise to disconnect cylinder from regulator
when plancha is not in use.
WHEN THE BURNER FLAME IS ACCIDENTALLY EXTINGUISHED
1. Close the LP tank valve.
2. Push and turn control knob clockwise to OFF position.
3. Inspect if the hose etc. connections are good, wait 5 minutes. After waiting 5 minutes,
re-start the appliance following the lighting instructions.
10
LIGHTING INSTRUCTIONS:
1. READ ALL INSTRUCTIONS BEFORE LIGHTING.
2. MAKE SURE ALL CONTROL KNOBS ARE IN THE
OFF POSITION.ALIGN THE NOZZLE OF THE LP
CYLINDER WITH THE REGULATOR AND
TURN COUNTER-CLOCKWISE TO CONNECT
CYLINDER WITH REGULATOR INLET.
3. SELECT THE BURNER TO BE
LIT. PUSH AND TURN THE
CONTROL KNOB OF THAT
BURNER COUNTER-
CLOCKWISE TO HIGH.HOLD
THE CONTROL KNOB PUSHED
DOWN FOR 2-3 SECONDS. IT
WILL LIGHT THE BURNER.
4. ADJUST THE FLAME BY
TURNING CONTROL KNOB
BETWEEN HIGH AND LOW.
5. REPEAT STEP 3 FOR LIGHTING THE
OTHER BURNER.
6. IF IGNITION DOES NOT OCCUR IN 5
SECONDS, TURN THE BURNER
CONTROL(S) OFF,WAIT 5 MINUTES, AND REPEAT
THE LIGHTING PROCEDURE.
7. TO TURN OFF, PUSH AND TURN EACH CONTROL
KNOB CLOCKWISE UNTIL IT LOCKS IN THE
OFF POSITION.
3. SÉLECTIONNEZ LE BRÛLEUR À ÊTRE
ALLUMÉ. POUSSE ET TOUR LE BOUTON DE
COMMANDE DU BRÛLEUR EN SENS
INVERSE À ÉLEVÉ. LE BOUTON DE
CONTRÔLE POUSSÉ POUR 2 À 3 SECONDES.
ON VA ALLUMER LE BRÛLEUR.
4. RÉGLER LA FLAMME À TOURNER LE
BOUTON DE COMMANDE ENTRE LA HAUTE
ET LA BASSE.
5. RÉPÉTER L'ÉTAPE 3 DE L'ÉCLAIRAGE AUTRE
BRÛLEUR.
6. SI L’APPAREIL NE S’ALLUME PAS EN 5 SEC
ONDES, FERMEZ LE ROBINET DU BRÛLEUR,
ATTENDEZ 5 MINUTES, ET PROCÉDEZ DE
NOUVEAU À L’ALLUMAGE.
7. COUPER, POUSSE ET TRANSFORME
CHAQUE BOUTON DE COMMANDE DANS LE
SENS DES AIGUILLES
DIRECTIVES D'ALLUMAGE:
1. LISEZ LES INSTRUCTIONS ADVANT
D’ALLUMER L’APPAREIL.
2. ASSUREZ - VOUS QUE TOUS LES
BOUTONS DE COMMANDE SONT DANS
LE OFF POSITION. ALIGNER LA BUSE DE
PL CYLINDRE AVEC L'ORGAN ISME DE
RÉGLEMENTATION ET COUNTER-CLOCKWISE
AVEC RÉGULATEUR INLET POUR RELIER
LA BOUTEILLE.
OFF/ARRÊT OFF/ARRÊT