Martel 311A-Ex Reference Manual Download Page 5

3

Warning

To avoid possible electric shock or personal injury:

• Do not apply more than the rated voltage. See specifications for supported ranges. 

• Follow all equipment safety procedures.

• Never touch the probe to a voltage source when the test leads are plugged into the

current terminals.

• Do not use the calibrator if it is damaged. Before you use the calibrator, inspect the

case. Look for cracks or missing plastic. Pay particular attention to the insulation
surrounding the connectors.

• Select the proper function and range for your measurement.

• Make sure the battery cover is closed and latched before you operate the calibrator.

• Remove test leads from the calibrator before you open the battery door.

• Inspect the test leads for damaged insulation or exposed metal. Check test leads

continuity. Replace damaged test leads before you use the calibrator.

• When using the probes, keep your fingers away from the probe contacts. Keep your

fingers behind the finger guards on the probes.

• Connect the common test lead before you connect the live test lead. When you

disconnect test leads, disconnect the live test lead first.

• Do not use the calibrator if it operates abnormally. Protection may be impaired. When in

doubt, have the calibrator serviced.

• Only operate the calibrator in non-hazardous areas or classified areas for which this

device is certified to operate in.

• When measuring pressure, make sure the process pressure line is shut off and

depressurized before you connect it or disconnect it from the pressure module.

• Disconnect test leads before changing to another measure or source function.

• When servicing the calibrator, use only specified replacement parts.

• To avoid false readings, which could lead to possible electric shock or personal injury,

replace the battery as soon as the battery indicator appears.

Caution

To avoid possible damage to calibrator or to equipment under test:

• Use the proper jacks, function, and range for your measurement or sourcing application.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for 311A-Ex
































Reviews: