background image

 

 
6.0 

Warranty 

 

MarTek Ltd. guarantees all products manufactured by 
MarTek Ltd. only against defects in materials and/or 
workmanship for a period of twelve (12) months 
commencing on the date the product is received by the 
customer.  THIS WARRANTY IS IN LIEU OF ALL OTHER 
EXPRESS OR IMPLIED WARRANTIES INCLUDING 
THOSE OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE. 
 
MarTek Ltd. will, at its option and its cost (excluding shipping 
expenses), repair, replace or refund the purchase price of 
any product manufactured by MarTek Ltd. which has a 
defect in materials and/or workmanship.  THIS IS 
CUSTOMER’S EXCLUSIVE REMEDY FOR BREACH OF 
WARRANTY.  IN NO EVENT WILL MARTEK LTD’S 
LIABILITY FOR DAMAGES (WHETHER ARISING FROM 
BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE, 
STRICT LIABILITY OR OTHERWISE) EXCEED THE 
PURCHASE PRICE OF THE PRODUCT CONCERNED 
NOR WILL MARTEK LTD. BE LIABLE FOR PUNITIVE, 
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES 
(INCLUDING WITHOUT LIMITATION LOST PROFITS) 
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES.

 

 
MarTek Ltd. reserves the right to disallow warranty repairs if 
the unit has been disassembled or misused, as determined 
by MarTek Ltd. in good faith.  Please contact us at (800)-
248-4958 for a return authorization.

 

 

MarTek Ltd. 

4782 Chimney Drive 

Charleston, WV 25302 

1-304-965-9220 
1-800-248-4958 

 
 

 

 

 

7.0

                               

 

Specifications 

 

MECHANICAL 

 
 

Holding magnets:   

Two magnets, each rated @ 55.1 lbs  

 

 

 

 

force, 12,600 Gauss. 

 
 

Projected life: 

 

20,000 operations 

 

ELECTRICAL 

 
 

Operating voltage:    

12 volts DC 

 
 

Fuse: 

 

 

3 amp 

 

Power supply: 

8 AA alkaline disposable batteries.  When 
used properly, one set of batteries should 
yield hundreds of operations. 

 

Control Cable: 

30 feet in length (9.1 meters), 5-conductor, 
extra-flexible, PUR insulation 

 

Controller: 

Requires two-hand operation.  The 
‘enable’ button must be depressed while 
depressing the ON or OFF buttons. 

 

A programmable micro-controller manages 
control inputs, linear actuators, and 
performs timing functions to protect the 
actuator in a stalled condition. Intelligent 
‘H-bridge’ motor drivers provide 
start/stop/braking actuator functions 
 

Summary of Contents for Chicken Switch K-15










Reviews: