MARSAL MB236 Service Manual Download Page 8

7

 

 

OPERATIONAL

 

DIFFICULTIES

 

&

 

POSSIBLE

 

CAUSES

 

TROUBLESHOOTING 

FIRST THING’S FIRST! 

 

Check

 

the

 

diameter

 

of

 

your

 

gas

 

connections.

 

Flex

 

lines

 

or

 

hard

 

plumbing

 

MUST

 

BE

 

¾”

 

or

 

bigger.

 

 

A

 

stainless

 

steel

 

flue

 

pipe

 

MUST

 

BE

 

installed

 

on

 

all

 

ovens

 

that

 

are

 

venting

 

into

 

a

 

hood.

 

 

A

 

draft

 

diverter

 

MUST

 

BE

 

installed

 

on

 

all

 

ovens

 

being

 

directly

 

vented

 

into

 

the

 

ceiling.

  

 

PROBLEM

 

POSSIBLE

 

CAUSES

 

PILOT

 

BURNER

 

GOES

 

OUT

 

1.

 

Pilot thermocouple not in center of flame. 

2.

 

Poor draft conditions snuff out flame (no flue pipe). 

3.

 

Too much draft pulls the flame away from thermocouple. 

4.

 

Air from fans or register blowing at front of oven. 

5.

 

Pilot flame too low. 

6.

 

Pilot orifice is dirty. 

7.

 

Thermocouple is defective. 

8.

 

Safety pilot valve defective. 

9.

 

Gas leak at pilot orifice fitting. 

BURNER

 

FAILS

 

TO

 

COME

 

ON

 

WHEN

 

PILOT

 

IS

 

ON

 

1.

 

Burner valve off located just above the thermostat. 

2.

 

Safety valve defective. 

3.

 

Thermostat out of calibration. 

4.

 

Thermostat is defective. 

5.

 

Burner orifice is plugged. 

Summary of Contents for MB236










Reviews: