MARSAL MB236 Service Manual Download Page 7

6

 

 

    

 

GAS

 

CONTROL

 

AND

 

PIPING

 

CONTROL

 

STACK

 

ASSEMBLY

 

REMOVAL

 

1.

 

Open baking compartment door and remove thermostat bulb from the top of the chamber. 
Slide the capillary tube to the left and into the control door area. 

2.

 

Disconnect pilot tubing at safety valve on control stack. 

3.

 

Disconnect the thermocouple from the safety valve. 

4.

 

Disconnect upper and lower unions on control stack. 

5.

 

Pull control stack assembly forward. 

6.

 

Replace control stack in reverse order from removal. 

AUTOMATIC

 

SAFETY

 

PILOT

 

VALVE,

 

MAIN

 

MANUAL

 

CONTROL

 

VALVE,

 

AND

 

THERMOSTAT

 

REMOVAL

 

1.

 

Remove Control Stack Assembly (see above). 

2.

 

Remove respective control from Control Stack Assembly. 

3.

 

Replace new control and other components in Control Stack Assembly in reverse order. 

 

ATTENTION:

 

THE

 

TSII

 

SAFETY

 

VALVE

 

CAN

 

BE

 

REPLACED

 

BY

 

REPLACING

 

THE

 

HEAD

 

ONLY,

 

LEAVING

 

THE

 

BODY

 

STILL

 

ATTACHED

 

TO

 

THE

 

CONTROL

 

STACK

 

ASSEMBLY.

 

PRESSURE

 

REGULATOR

 

REPLACEMENT

 

#71881

 

(N)

 

OR

 

#71882

 

(P)

 

The pressure regulator is located just above the control stack in the control compartment. Before 
replacement, gas service to this point must be shut off before disconnecting.  

 

Figure 4

Figure 5 

Summary of Contents for MB236










Reviews: