Owner’s Manual -
30” Metal Oscillating Pedestal Fan
3
Owner’s Manual -
30” Metal Oscillating Pedestal Fan
3
ASSEMBLY INSTRUCTIONS
OPERATION INSTRUCTIONS
,
e
f
a
s
a
n
o
n
a
f
e
h
t
e
c
a
l
P
.
1
surface where it can
not fall or be pulled by the cord.
2. T
o adjust
air
up
and down
: Tilt the
fan head
o the desired angle.
.
d
e
e
p
s
d
e
ri
s
e
d
r
o
f
h
c
ti
w
s
y
r
a
t
o
r
e
h
t
n
r
u
T
.
3
1=Low, 2=Med., 3=High
4. Always turn and unplug the fan after using.
pipe was secured onto the support post tightly.
5.
Insert extension pipe into support post, black ring
onto support post by tightening back three screws
from Step 4. Adjust extension pipe to your desired
height and secure it by tightening back the height
adjustment knob.
WARNING:
To avoid injury
,
never put your head over
the extension pipe during or before the ex
tension
Assemble fan blade onto motor
shaft by tightening screw and
washer. Make sure screw is
tightened.
10.
Remove the hexagon bolts, bolt
sheaths and washers, hexagon head
square strength bolts, hexagon
lace nuts from the top of the extension
tube and save them for step 7.
6.
Assemble front guard to
rear guard by attaching both
guards together with clips on
the rim of front guard.
11.
Install the fan head on the exten-
sion tube by fastening and hexagonal
bolts, bolt jackets, washers, hexagonal
square
bolts and hexagonal
lace nuts from step 6.
7.
Secure the assembly of front
guard and rear guard by tight-
ening a screw and nut at the
bottom of the guards.
12.
OSCILLATION INSTRUCTIONS
Set rear guard in proper
position and attach it to
fan head by securing back
the nuts and washers from
Step 8.
9.
Remove four sets of hexagonal
nuts, spring washers and
washers from fan head. Save
them Step 9.
8.
To make the fan head oscillate: loosen the screw and
move to position A and tighten.
NOTE:
the screw is preset at position A at the factory.
To stop the fan head oscillating: loosen the screw and
move to position B and tighten
Tighten it back.
CAUTION:
Switch the fan before adjusting fan
head oscillation.
Position A
-
To make the fan
head oscillate
Position B
-
To stop the fan
head oscillate
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
extension tube and save them to step 7.
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
extension tube and save them to step 7.
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
extension tube and save them to step 7.
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
extension tube and save them to step 7.
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
Remove the hexagon bolts, bolt sheaths and
washers, hexagon head square strength bolts,
hexagon flange lace nuts from the top of the
extension tube and save them to step 7.
Install the fan head on the extension tube by
fastening the hexagonal bolts, bolt jackets,
washers, hexagonal square stiffening bolts
and hexagonal flange lace nuts in step 6.
For additional information on the product or replacement parts, call
our Customer Service Department at Mars’ tel no.
