Marquee 0182364 Assembly Instructions Manual Download Page 4

Please read these instructions completely before starting assembly

Safety Advice

The gazebo must be positioned and fixed on a flat level surface.

Dispose of all plastic bags safely. Keep them out of the reach of children.

Keep children and pets away from the assembly area until the work is completed.

Always wear proper safety gear including work shoes, gloves.

Do not attempt to assemble the gazebo in medium windy or wet condition.

Do not place your gazebo in an area exposed to excessive wind.

If using power tools or a ladder, always follow the manufacturer safety instructions.

Hot items such as grills, blowtorches, heaters etc. must not be stored in the gazebo.

Do not cook or lit fireworks near the gazebo.

Avoid vandalism, abuse, falling or thrown objects, or accumulation of snow.

Tips:

     Please don't destroy boxes until completely assembled. 

              Do not tighten bolts immediately. You can install loose by cordless drill with Philips head. Adjust to make all 
              components in place before you tighten all screws by Philips Screwdriver.  Power tools may over tighten fittings.
              Cool temperature condition is recommended for easy assembly.
              Make sure you have all the necessary parts. The List of Parts has the corresponding step number referenced 
              to each part. We recommend that while you go through the list, make staging areas for each step and place the 
              parts necessary for each step in these areas. This will save you time and effort during assembly.

03 / 18

List of Parts..................................................................................................    1-2

Table of Contents.........................................................................................      

 

3

STEP 1   Assemble the Leg posts.....................................(ca. 5min)...........      

 

4

STEP 2   Assemble the Beams..........................................(ca. 5min)..........       5

STEP 3   Attach the Rails to the Beams............................(ca. 10min).........      6

STEP 4   Attach short Beams to the Leg posts.................(ca. 10min).........      7

STEP 5   Attach long Beams to the Leg posts..................(ca. 15min).........      

 

8

STEP 6   Install the Beam covers......................................(ca. 10min).........      9

STEP 7   Assemble four Corner ribs.................................(ca. 5min)...........     10

STEP 8   Put up Lower top plate and Corner ribs.............(ca. 15min).........     11

STEP 9   Install the Mid ribs..............................................(ca. 5min)...........     12

STEP 10  Install the Upper top plate.................................(ca. 5min)...........     13

STEP 11  Assemble the large Roof panels........................(ca. 20min).........     14

STEP 12  Put up the Roof panels.......................................(ca. 15min).........     15

STEP 13  Install Edge protectors and Rib caps.................(ca. 15min).........     16

STEP 14  Put up Fabric side panels and Mosquito nets....(ca. 10min).........     17

STEP 15  Secure the Gazebo to the ground.......................(ca. 5min)...........     18

Thank you for choosing the Havana Gazebo!

All steps can be completed by 4 people. The assembly take about two and a half hours.

Proper tools: Two ladders, Philips screwdrivers, Gloves, Spirit Level.

Note: Your gazebo is a non-permanent structure. It is designed for leisure use 

              and is not a shelter against adverse weather conditions.

Table of Contents

Summary of Contents for 0182364




















Reviews: