Markilux 6000 Fitting Instructions Manual Download Page 10 | Manualshive

Page: 10 / 11

Markilux 6000 Fitting Instructions Manual Download Page 10

10

8. Awning with lighting (two lamps per unit)
8.1 Overview

1

Lighting profile

2

Cap

3

Holder

4

Acrylic glass lighting tube colorless satin

finish

5

Fluorescent lamp

Osram FQ 39 W / 827

6

Mask

7

Starter casing

Electrical work: Electrical installations must be carried by a qualified electrician according to VDE 0100.

8.2 Lighting with dimmer

8.2.1

The cable for the lighting connection is

marked with this sticker.

The wiring diagram must definitely be observed, a
faulty connection can lead to the destruction of the
device!

Wire color

Terminal

(1) gray

Control voltage dimmer 10V (+)

(2) black

Control voltage dimmer 10V (-)

(3) brown

230V~ voltage supply phase

(4) blue

230V~ voltage supply neutral
conductor

(5)
green/yellow

230V~ voltage supply protective
conductor

8.2.2

For the connection of the supply and control

cable, 5 approved screw terminals or non-screwed
terminals with a rated voltage of at least 230 V~
are required.

Attention Danger to Life:

Electrical operation

without  protective  conductor  connection  is  not
permitted! It is to be observed, that during operation
the  protective  conductor  (5)  green/yellow  is  neither
interrupted in/on the product nor by the mains cable.

All  electrical connections  and  connection  leads must
definitely  be  checked  after  being  connected  and
before the first trial operation!

8.2.3

Technical data of a lamp:

Power supply:

230 VAC

50 Hz (10/16A)

Max. wattage:

39W

Lamp:

OSRAM FQ39W/827

System of protection:

IP54

Supply cable cross-section: min. 1.0 mm²

«
...
8
9
10
11
»

Summary of Contents for 6000












Reviews:

No comments