Market Forge Industries STP-6G Installation And Operation Manual Download

Page: 45 / 52

6.10 SOLENOID FILL VALVE STRAINER SCREEN

CLEANING

The solenoid operated fill valves contain a built-in

strainer screen inside the valve body. This screen must be

removed and cleaned periodically (depending on usage and

water quality) to remove any debris or lime build-up which will

accumulate during normal operation. The procedure is as

follows:

Procedure:

I. Remove the left large side panel by removing the screw

from the center of the bottom edge of the panel. Gripping

one of the louvers, slide the panel upwards until the

bottom edge of the panel is free to swing out slightly

away from the unit. Slide the panel down until its top

edge is clear of the top cap of the unit.

2. Unscrew screen plug from valve and remove screen.

3. Clean screen and reassemble screen and screen plug

into valve body.

4. Replace large side panel by placing the panel against

the side of the unit. Be sure that the top edge of the side

panel slides under the top cap of the unit. Slide the

panel upwards until it stops. Then, while pushing the

panel in towards the unit, slide it down into position.

Replace screw.

Table 6.10 - Tempering

Tank Assembly Parts List

ITEM

QTY

DESCRIPTION

PART NO.

Adapter Fitting, 1/2" mNPTto 3/4" Hose Barb, Brass

E08-5029

Branch Tee, 1/8" m NPT to 1/4" Hose Barbs, Brass

E08-5009

Cross Fitting,

Ml"

NPT, Brass

E08-5011

Drain Valve, N.O.

(note orientation when installing)

E08-5021

Elbow Union, 1/2" NPT Brass

E09-4844

Eibow, 1/4" mNPT to 1/4" Hose Barb, Brass

E08-5005

Elbow, 1/8" mNPT to 1/4" Hose Barb. Brass

E08-5063

Fexible Drain Tubing, 3/4" I.D., 2.5" long

E08-5013

Fexible Drain Tubing, 3/4" I.D., 4" long

E08-5013

Float Switch, N.C.

(note orientation when installing)

E08-5023

1 1

Hose Clamps, for 1" O.D. Tubing

E08-5014

Pipe Stub, 1/2" mNPT, Threaded One End, Brass

E08-5008

Reducer, 1/2" mNPT to 1/8"fNPT Brass

E08-5007

Spray Nozzle, Solid Jet, Brass

E08-5010

Steam Trap Valve

E08-5012

3/4" Bead x 1/2" mNPT 90° Elbow, Brass

E08-5029

Tempering Tank Weldment

E91-7552

Thermostat, N.O., 130°F

E08-6514

Water Inlet Valve, N.C. (note

orientation when installing)

E08-4821

Water Supply Manifold

E91-5676

10-32 Nyloc Nut, zinc plated

E08-3841

10 Washer, zinc plated

E08-4010

MARKET

FORGE

INDUSTRIES, INC.

35 GARVEY STREET EVERETT, MA 02149

6.22

TEL: 6 17 387

100 TELEX: 94-94 1 4

FAX: 617 387 4456 OUTSIDE MA 800 227 2659

6. Maintenance

Summary of Contents for STP-6G





















































Search results

Summary of Contents for STP-6G

Reviews:

Related manuals for STP-6G

Brands by name

Popular brands

Market Forge Industries STP-6G, Installation And Operation Manual

Search results

Summary of Contents for STP-6G

Reviews:

Related manuals for STP-6G

Brands by name

Popular brands