Market Forge Industries M24E24A Installation, Operating, Maintenance And Parts Manual Download Page 1 | Manualshive

Page: 1 / 31

Market Forge Industries M24E24A Installation, Operating, Maintenance And Parts Manual Download Page 1

ELECTRIC OPERATED BOILER

INSTALLATION, OPERATING, MAINTENANCE AND PARTS MANUAL

MODELS:

□

M24E24A

□

M24E32A

□

M24E36A

□

M24E42A

□

M24E48A

□

M36E24A

□

M36E24A

□

M36E32A

□

M36E36A

□

M36E42A

□

M36E48A

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OP-
ERATION AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING
OR SERVICING THIS EQUIPMENT.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN
THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

POST INSTRUCTIONS IN A PROMINENT LOCATION TO BE FOLLOWED IN THE EVENT
THE USER SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY CONSULTING
THE LOCAL GAS SUPPLIER.

Printed in U.S.A.

Form No S-3112

Rev. D

35 Garvey Street, Everett, MA 02149

Tel: (617) 387-4100, (866) 698-3188, Fax: (617) 387-4456, (800) 227-2659

[email protected], www.mfii.com

1
2
3
...
»

Summary of Contents for M24E24A
































Reviews:

No comments