marinco SPLR-2 Instructions Manual Download Page 1

502-2 & 503-2   instructions

Instructions

marinco.com

Installing and Using the  

Precision Spotlight

IMPORTANT! 

READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.

The Marinco Precision spotlight uses a super bright 100 Watt, replaceable H3 Halogen bulb 

that produces a rich yet intense beam that can illuminate objects up to 1,000 ft away. It is 

IP56 Weatherproof rated for extreme enironments, with a UV weather resistant housing and 

fully enclosed tilt function driven by quiet motors that can withstand extreme temperatures 

(5°F to 113°F or -15°C to 45°C). It has been designed and tested to withstand the harsh 

marine environments including high humidity, salt water spray, shock, and vibration. 

Innovative construction allows for upside down mounting and reverse motion programming. 

Precision circuitry allows for remarkable aiming and tracking with two speed choices. The 

spotlight has a 30 minute shut-down timer. If the spotlight is left unattended for more than 

30 minutes, the spotlight will turn off. The shut-down has no effect on the SOS function of 

the spotlight.
The Precision remotes have glow in the dark buttons and include one touch Automatic 

Sweep and SOS options. The wireless remotes transmit a signal up too 200ft (60m). While 

the spotlight comes with a wireless bridge remote there are two more optional remotes: 

a wireless handheld remote w/lanyard (SPLR-1) and a hard wired bridge mount remote 

(SPLR-3). 

Package Includes: 

•  Spotlight with 12 Volt bulb installed

•  Mounting bracket (no fasteners included)

•  Wireless Bridge Remote (SPLR-2)

•  Instruction manual

•  Additional 24 Volt bulb**  

     **(models SPL-12W, SPL-12B, SPL-12C only)

MODELS: SPL-12W, SPL-12B, SPL-12C

SPLR-2 (included)

SPLR-1

SPLR-3

Español ................................. 8
Français .............................. 16

Summary of Contents for SPLR-2

























Reviews: