marinco SPLR-1 Instructions Manual Download Page 1

502-2 & 503-2   instructions

Instructions

marinco.com

Installing and Using the  

Precision Spotlight Remotes

Required for Installation:

•  Two (2) No. 6 stainless steel pan head screws (Length and 

type of screws to be determined by mounting surface) 

•  Two (2) #16 AWG butt wire connectors

Mounting the wired and wireless bridge remote
1.  The remotes are all IP54 weather resistant. 
2.   Please choose a mounting location based on the gasket 

supplied with the remote (large hole should be towards top). 

3.  Drill holes the correct size for the mounting screws. The holes 

through the remotes are sized for a No. 6 pan head screw. 
The length and thread type will need to be determined by the 
application. Remove and set aside the 2 screw covers. 

4.  Drill hole for the wiring. Note that the hole needs to be 5/8" to 

allow the unit to sit flat.

5. 

If mounting the wireless bridge remote it will require a 12V 
or 24V power source. 

If mounting the hard wired bridge 

remote then it does not need a local power source and 
instead uses the purple and yellow wires connecting from 
the spotlight to the remote. These two wires will supply the 
remote with power and control the spotlight. The terminals on 
the remote can handle a 16 AWG to 26 AWG wire. Maximum 
torque on the terminals is 2.21 in lbs (.25 nm).

6.  Feed wires through drilled surface hole and gasket from below. 
7. 

For the wireless bridge remote attach the power source 
wires to the remote (+) positive and (-) negative terminals.  

For the hard wired bridge remote attach the 2 wires from the 
spotlight. The yellow wire needs to connect to the (+) positive 
and the purple wire needs to connect to the (–) negative. 
Maximum torque on the terminals is 2.21 in lbs (.25 nm)

8.  Place remote in desired location, align holes and tighten down.
9.  Apply screw covers to remote to hide screws. 

Pairing of mounted and hand held wireless remote to spotlight 
1.  Disconnect all power to the spotlight. 
2.  Apply power to wireless remote. Press and hold the power 

button on the wireless remote. 

3.  While pressing the power button connect power to the spotlight. 
4.  After a few seconds you will hear the relay click and the light 

will turn on. 

5.  When the light turns on the paring is complete, release power 

button. 

 

 

 

 

Español ......................................... 5
Français ........................................ 8

Summary of Contents for SPLR-1













Reviews: