Marey ECO110 Instruction Manual Download Page 14

5. Before beginning any work on the electric installation, be sure that the main breaker

panel switch is OFF to avoid any danger of electric shock. All mounting and plumbing

must be completed before proceeding with electrical hook-up.

OPERATING INSTRUCTIONS

1. Turn on the circuit breaker to bring electrical power to the unit.

2. Open the water faucet for a few minutes until the water flow is continuous and all the

air is purged from the water pipes. The unit must operate after the breakers are turned on

3.After the unit is supplied with power, a beep sound can be heard and LED lights appear

for 2 seconds; if there is no other display, the appliance keeps standby.

4. Press         to turn ON/OFF the appliance. When the unit is ON, LED lights show the

actual outgoing water temperature. When the appliance stops working, after 5 seconds,

the screen switches on the screen saver. The display screen light will be off. If somebody

touches the screen, the Iight will be on again.

5. Press

             

and            to adjust the outlet water temperature. Temperature setting

range is 30-52°C/ 86-125°F.

- If the unit has been paused, you may initially get a short burst of very hot water when

you turn it on again. Please run the water through for a few seconds to let the temperature 

settle down. Please check the hot water with your hand before taking a shower.

- If the unit is not used in winter, drain out the water completely so that the heater does

not freeze.

- Please clean the inlet filter and the shower periodically in order to keep a proper water flow.

6. Press

          

to change the temperature display between Fahrenheit and Celsius degrees.

7. There is an automatic memory function to avoid repetitive operation. When you turn on the

appliance, the default setting temperature will be the same as last time setting.

14

Summary of Contents for ECO110

















Reviews: