ATTENTION!
On first use the soldering iron may produce smoke, this is just grease used in manufacturing
burning off, it is not harmful to the product or user.
FEATUREs
• With a mini drawer on the base to hold the spare parts
• 30W temperature controlled soldering station with adjustable range from 160’C to 550’C
• High quality ceramic heater ensure a fast and quick heating in short time and a long
service life .
• LCD display to indicate the temperature , with blue backlight
• Safeguard iron holder
• A sponge and recessed area provide a convenient method for cleaning the tip
sAFETY NOTEs:
Please note the following safety notes to avoid malfunctions, damage or physical injury:
• Persons with limited physical, sensorial or mental abilities are not allowed to use the unit,
unless they are supervised for their safety by a qualified person or are briefed by the re-
sponsible person how to use the unit.
• Do not leave packaging materials in the range of children, they may become dangerous
toys.
• Do not leave the unit unsupervised while it is turned on. Keep children away while the unit
is in use. Do not allow children or people in need of supervision to use the unit.
• Do not continue using the unit after it, or the power cord, have been damaged.
• Do not run the power cord around sharp edges or over hot surfaces.
• Do not touch any hot surfaces. The soldering tip becomes very hot during operation.
• Be extra careful when using the soldering iron around combustible materials.
• Place the soldering station on a solid, level surface.
• During soldering harmful fumes may escape. Work only in well aired spaces or under a
suitable air extraction system.
• Protect your eyes and body from splashing hot solder by wearing suitable protective
equipment.
• Turn off the unit and pull the power plug while you are not using the unit or before clea-
ning. Do not pull on the power cord, always grasp the plug itself.
• Allow the unit to cool down before cleaning or storing.
• Do not use the unit outdoors.
• Do not immerse the unit in liquids of any kind. Do not use the unit to heat plastic or
liquids.
• Do not disassemble the unit and do not try to repair it yourself. It does not contain parts
serviceable by you.
GHOsT30 -
User’s manual
User’s manual
- GHOsT30
OPERATION:
• Unpack the soldering station and check all parts. Damaged parts must not be put into
operation.
• Put the holding rack for the soldering iron sideways in the soldering station, wet the cle-
aning sponge in the sponge rack with water.
• Put the soldering iron in the holding rack
• Place the soldering station on a solid and dry surface
• Connect the mains plug to a socket and turn on the soldering station by using the power
switch (I=ON/0=OFF).when turned on, the power switch is lit. The LCD screen will show
the set temperature as 300°C.
• Then press the ”+” or ” –“ button under the LCD screen to adjust the temperature. Each
press will be +/- 10°C. Do such pressing until you get your target set temperature. The
soldering iron will reach your target temperature in 10 minutes .
• Wait about 2-3 minutes until the soldering tip reaches the adjusted temperature, test the
temperature by touching the soldering tip with solder, if the solder melts away easily you
can start soldering.
• Tin the hot soldering tip with solder; wipe off excessive solder on the wet cleaning sponge.
• Heat up the soldering location with the soldering tip and add solder.
• Let the soldering point cool down.
• Clean the soldering tip on the wet sponge after each soldering
• After finishing the soldering, put back the soldering iron in the rack and turn off the sol-
dering Station at the main switch.
• Put the soldering iron on the rack to cool down naturally .
• For larger soldering tip adjust the temperature up wards to perform the soldering as fast
as possible and as long as necessary.
• Lower the temperature during breaks, this saves energy and extends the durability of the
soldering tip.
• Do not file off the soldering tip, or it will be damaged.
• Always put the soldering iron on the holding rack when it is heating up or during breaks
from soldering
• Make sure the contracts for soldering on the work place are clean
• Only use solder for electronics. Acidic solder can damage the soldering tip or the work
piece
• Never touch the hot soldering tip.
• Let the soldering iron cool down after use.
• The soldering iron should not be dunked into water
• During breaks, the soldering iron has to be placed in the holding rack.
