68
IC29 : CS4382A-CQ
MUTEC1
MUTEC234
41
22
Mute Control
(
Output
) - The Mute Control pins go high during power-up initialization, reset, muting,
power-down or if the master clock to left/right clock frequency ratio is incorrect. These pins are intended
to be used as a control for external mute circuits to prevent the clicks and pops that can occur in any sin-
gle supply system. The use of external mute circuits are not mandatory but may be desired for designs
requiring the absolute minimum in extraneous clicks and pops.
,-
,-
,-
,-
,-
,-
,-
,-
39, 40
38, 37
35, 36
34, 33
29, 30
28, 27
25, 26
24, 23
Differential Analog Output
(
Output
) - The full scale differential analog output level is specified in the
Analog Characteristics specification table.
VA
32
Analog Power
(
Input
)
-
Positive power supply for the analog section. Refer to the Recommended Oper-
ating Conditions for appropriate voltages.
VLS
43
Serial Audio Interface Power
(
Input
)
-
Determines the required signal level for the serial audio inter-
face. Refer to the Recommended Operating Conditions for appropriate voltages.
Control Port Definitions
SCL/CCLK
15
Serial Control Port Clock
(
Input
) - Serial clock for the serial control port. Requires an external pull-up
resistor to the logic interface voltage in I
2
C mode as shown in the Typical Connection Diagram.
SDA/CDIN
16
Serial Control Data
(
Input/Output
) - SDA is a data I/O line in I
2
C mode and requires an external pull-up
resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDIN is the input
data line for the control port interface in SPI mode.
AD0/CS
17
Address Bit 0 (I
2
C) / Control Port Chip Select (SPI)
(
Input
) - AD0 is a chip address pin in I
2
C mode;
CS is the chip select signal for SPI format.
Stand-Alone Definitions
M0
M1
M2
M3
17
16
15
42
Mode Selection
(
Input
) - Determines the operational mode of the device as detailed in Tables 6 and 7.
DSD Definitions
DSD_SCLK
42
DSD Serial Clock
(
Input
) - Serial clock for the Direct Stream Digital audio interface.
DSD_EN
7
DSD-Enable (Input)
- When held at logic ‘1’ the device will enter DSD mode (Stand-Alone mode only).
DSDA1
DSDB1
DSDA2
DSDB2
DSDA3
DSDB3
DSDA4
DSDB4
3
2
1
48
47
46
45
44
Direct Stream Digital Input
(
Input
) - Input for Direct Stream Digital serial audio data.
Pin Name
#
Pin Description
Summary of Contents for SR-4001
