22
ENGLISH
TROUBLESHOOTING
If a problem should arise, first check the following.
1.
Are the connections correct?
2.
Have you operated the receiver according to the operating instructions?
3.
Are the speakers and other components operating properly?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
Symptom
Power does not turn on
when POWER
ON/STANDBY switch is
pressed.
There’s no sound
coming from the
speakers?
Sound is coming from
only one speaker?
Nothing happens when
remote control buttons
are pressed.
Cause
• Mains cord’s plug is not
plugged into wall outlet.
• The speaker cables are not
connected properly.
• The volume is set at minimum.
• The CR401 is muted.
• A pair of headphones is
connected.
• The wrong input source is
selected.
• A connecting cable may be
damaged.
• The other speaker’s cable is
not connected properly.
• Are the batteries dead?
• Is the remote control unit too
far away?
• Is there an obstacle between
the remote control unit and the
main unit?
• You have pressed the wrong
button.
• Batteries are not set in their
proper direction (
ª
and
·
).
Measures
• Plug the mains cord in
properly.
• Check the speaker
connections and make sure
that none of the wires are
touching each other, other
connectors, or any metal parts.
• Turn up the volume.
• Unmute the CR401.
• Turn down the volume, then
disconnect the headphones .
• Check the input source setting.
• Check your connecting cables
for signs of damage and
replace as necessary.
• Check the speaker
connections and make sure
that none of the wires are
touching each other, other
connectors, or any metal parts.
• Replace the batteries with new
ones.
• Operate from closer to the
main unit.
• Remove the obstacle.
• Press the desired button.
• Set the batteries in the proper
direction.
Page
9
11
19
11
11
10
9
4
4
4
7
4
Symptom
Cause
Measures
Page
Hissing noise is heard
on FM broadcasts.
Hissing or buzzing
sound is heard on AM
broadcasts.
Booming sound
(humming) is heard in
AM broadcasts.
Reception is noisy,
intermittent, and the
indicator
flickers?
The radio presets no
longer work?
The RDS (Radio Data
System) doesn’t seem
to work?
CD playback skips?
Noise is generated.
• A strong light source is
interfering with the CR401’s
remote sensor.
• Antenna cable is not properly
connected.
• Antenna is not pointing in the
right direction.
• Radio waves are weak.
• Noise from a TV or
interference in the signals sent
from the broadcast station.
• Signals transmitted over the
main cord are modulated by
the power source frequency.
• You’re too far away from the
transmitter. Or, your FM
antenna is in the wrong
position or pointing in the
wrong direction. Or, the
station’s signal strength is
poor.
• The power cord has not been
connected to a wall outlet, or
the power has been turned off
for an extended period.
• The current FM station does
not support RDS.
• The signal strength is poor, or
there’s too much interference.
• The CR401 is subject to
vibration.
• The disc is dirty.
• The disc is very scratched.
• DTS CD is being replayed.
• Make sure that the CR401 is
not subjected to direct sunshine
or inverter-type fluorescent
lights. Relocate if necessary.
• Connect the leads properly.
• Point the antenna in the right
direction.
• Install an outdoor antenna.
• Turn off the TV.
• Change the position of the
loop antenna.
• Install an outdoor antenna.
• Insert the plug in the opposite
direction.
• Install an outdoor antenna.
• Switch the FM Mode to Mono.
• Adjust the position, height, and
direction of your FM antenna.
• Install an outdoor FM antenna,
preferably one with many
elements. Installing an out-
door antenna is a specialist’s
job, so contact your nearest
dealer for advice.
• Preset your favourite radio
stations again. The power cord
must be plugged into a wall
outlet a few times each month
in order to preserve the presets.
• Tune into a station that
supports RDS.
• Install an outdoor FM antenna,
change the position or
direction of your outdoor FM
antenna, and keep it away
from fluorescent lights.
• Install the CR401 somewhere
free of vibration.
• Remove the disc and clean it.
• Buy a new disc.
• Do not replay DTS CD, which
is not supported by the CR401.
4
8
8
8
8
8
8
9
8
15
8
8
16
17
8
2
3
3
2
CR401N̲01 Eng 05.11.18 4:55 PM ページ22
All manuals and user guides at all-guides.com
all-guides.com
