Mantis BF28BM-4 Installation Instructions Manual Download Page 1

Page 1

INSTALLATION INSTRUCTIONS

POWER-VENT 

HIGH-EFFICIENCY 

FIREPLACE WITH 

BAY WINDOW MANTIS MODELS

BF28(B,C,G)M(N,P)-4

BI28(B,C,G)M(N,P)-4

BP28(B,C,G)M(N,P)-4

FIREPLACE MANTIS MODELS

FF28BM(N,P)-2

FI28BM(N,P)-2

FW28BM(N,P)-2

WARNING: If not installed, operated and maintained in 

accordance  with  the  manufacturer’s  instructions,  this 

product could expose you to substances in fuel or from 

fuel combustion which can cause death or serious ill-

ness.

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

—  Do  not  store  or  use  gasoline  or  other  flammable 

 

vapors and liquids in the vicinity of this or any other  

appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

 

•  Immediately  call  your  gas  supplier  from  a 

 

neighbor’s  phone.  Follow  the  gas  supplier’s  

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation  and  service  must  be  performed  by  a  

qualified  installer,  service  agency  or  the  gas  sup

-

plier.

WARNING: If the information in these instructions are 

not  followed  exactly,  a  fire  or  explosion  may  result 

 

causing property damage, personal injury or loss of 

life.

This  appliance  may  be  installed  in  an  aftermarket, 

permanently  located,  manufactured  home  (USA  only) 

or mobile home, where not prohibited by state or local 

codes.
This appliance is only for use with the type of gas indicated 

on the rating plate. This appliance is not convertible for 

use with other gases, unless a certified kit is used.

EMPIRE

EMPIRE

Comfort Systems

Young children should be carefully supervised when they 

are in the same room as the appliance. Toddlers, young 

children  and  others  may  be  susceptible  to  accidental  

contact  burns.  A  physical  barrier  is  recommended  if 

there are at risk individuals in the house. To restrict ac-

cess to a fireplace or stove, install an adjustable safety 

gate to keep toddlers, young children and other at risk 

individuals out of the room and away from hot surfac-

es.

WARNING

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

Attention: Check local codes for venting requirements.

Summary of Contents for BF28BM-4













































Reviews: