manualshive.com logo in svg

Manson Engineering Industrial HCS-3600 USB, User Manual, Page: 2 / 9

Share
Download
Manson Engineering Industrial HCS-3600 USB User Manual Download Page 2

5  .    

  CONTROLS AND INDICATORS

 

 

(1) LED panel meter display with CC/CV Indictor
(2) Rear Control Indicator 

(lights up when using Preset/ Remote Control/ Set mode)

(3) Output Voltage Control Knob 

(control both the main and auxiliary output voltage)

(4) Output Current Control Knob 

(control both the main and auxiliary output current limit)

(5) Power ON/OFF Switch
(6) Aux. output terminal (max 5A)

Note:

HCS-3600: The total rated current (Aux.+Main) is 60A
HCS-3602: The total rated current (Aux.+Main) is 30A
HCS-3604: The total rated current (Aux.+Main) is 15A

(7) Output Terminal 

(Rated 60A for HCS-3600/ Rated 30A for HCS-3602/ Rated 15A for HCS-3604)

(8) Remote Sensing Terminal 

(for model HCS-3600 only)

(Warning!:  Shorting  the  remote  sensing  terminal  or  Connect  sensing  terminal  in  reverse  polarity  will
damage the power supply)

(9) Mode Selection Switch 

(Normal, Preset, Remote Control, Set Modes)

(10) Recall Selection Switch
(11)  Remote Control Terminal
(12) Cooling Fan Air Intake Grille
(13) AC Input Plug

Front

Rear

Summary of Contents for HCS-3600 USB










Reviews:

No comments