HYPER150 EC
EC Inline Axial Duct Fan with App Control
IMPORTANT
This EC inline axial duct fan must be installed by a registered electrician and its installation and connection to the power supply must comply with all
current wiring rules and regulations including the latest edition of AS/NZS3000 .
The power supply cable must be suitably rated by a registered electrician to satisfy the total load on that circuit.
The 10m control cable connects the wall controller to the EC inline axial duct fan as shown below. The EC inline axial duct fan should not be powered
while connecting the controller. A FAN2444 fully adjustable fan run-on timer (not supplied) must be used If timer switching is preferred.
EC INLINE AXIAL DUCT FAN INSTALLATION AND ELECTRICAL CONNECTION MUST
BE CARRIED OUT BY A REGISTERED ELECTRICIAN
WARNING
1.
This EC inline axial duct fan may only be used as recommended by the manufacturer in this manual. Any other use not recommended by the
manufacturer may cause fi re, electric shock, or injury to persons. Contact the manufacturer, or local agent, if required.
2. Isolate the mains supply before making any electrical connections. This system should be installed by a registered electrician.
3.
Ensure the EC inline axial duct fan is properly earthed.
4. The EC inline axial duct fan must be able to be isolated from the power by means of a disconnect switch meeting current electrical regulations.
5. The EC inline axial duct fan is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for
their
safety.
6.
Children should be supervised to ensure that they do not play with the EC inline axial duct fan.
IMPORTANT CONSIDERATIONS
Planning can make a big difference to the installation time and your satisfaction with the operation of the unit.
1.
Remove the unit from its packaging and check to make sure it is in good condition before using.
2.
Do not let children play with packaging.
3.
Check the household voltage to ensure it matches the EC inline axial duct fan’s rated specifi cation.
4.
Check the power cord and plug carefully before using to ensure there is no damage.
5.
Before unplugging the power cord, be sure to turn off the power. When energizing the unit, be sure your hands are dry to prevent electric shock.
6.
This EC inline axial duct fan is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials away from the
EC inline axial duct fan and keep them away from the sides and rear.
7.
Do not use near or in the immediate vicinity of a bath or swimming pool or any wet areas.
8.
To protect against electric shock, do not immerse cord or plug in water or any other liquids.
9.
Do not insert or allow foreign objects to enter any ventilation openings, as this may cause an electric shock, fi re or damage to the EC inline axial duct
fan.
10. Do not put fi ngers or foreign objects into the grille while in operation.
11 Any changes, or modifi cations, made, or attempted, to this product, without the prior written approval of the manufacturer, will void any, and all,
stated
warranties.
12. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and
outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.
13. Do not use it in areas where gasoline, paint, or fl ammable liquids are used or stored.
14. This product contains recyclable materials. Do not dispose of this product as unsorted council waste. Please contact your local council for
the nearest collection point.
15. Ensure that the EC inline axial duct fan is switched off from the supply mains before removing the guard
16. Ensure that the EC inline axial duct fan is to be installed so that the blades are more than 2,3 m above the fl oor
17. Ensure that precautions must be taken to avoid the back-fl ow of gases into the room from the open fl ue of gas or other fuel-burning appliances
18. For equipment with Type Y attachment, if the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualifi ed
persons in order to avoid a hazard.
ELECTRICAL CONNECTIONS
Mains
Control
Speed
Control
Potentiometer
BROWN
WHITE
BLUE
BLACK
GREEN/YELLOW
RED
LIVE
EARTH
NEUTRAL