background image

Part Number 000007646 Rev 02 5/20 11

Section 2 

Installation

Installation Procedures

n

Warning

Do not attempt to move a dispenser without first removing 

the ice machine. The combination can be unstable and 

could tip, causing serious injury.

1.  Review the Pre-Installation Checklist; then make sure 

all utility and space requirements are present at the 

installation site.

2.  Remove the carton top from the dispenser.
3.  Remove the legs and other accessories from inside the 

dispenser bin.

4.  Remove the carton from the sides of the dispenser.
5.  Remove the dispenser from the shipping pallet.
6.  Flatten the shipping carton.
7.  Lay the dispenser on its back; on the carton.
8.  Thread the legs into the bottom of the dispenser.
9.  Set the dispenser upright.
10. Place the dispenser in the desired location.
11. Make sure the dispenser bin top is level. A level bin is 

important for proper operation of the ice machine.

12. Place the ice machine on top of the dispenser at this 

time. 

13. Connect the drain of the dispenser to the floor drain. 
14. Follow local plumbing codes for drain installation. 
15. If the dispenser has a water valve, connect your 

water line to the water connection at the back of the 

dispenser.

16. Test all drain and water lines for leaks.
17. Plug the dispenser into the proper electrical outlet. 
18. Clean and sanitize all equipment. Follow cleaning and 

sanitizing instructions in this manual.

19. Adjust the ice machine according to the instructions 

provided with the ice machine.

20. Install ice baffle inside the ice maker compartment. 

Follow installation instructions supplied with ice baffle. 

21. Install foam gasket on the bottom of the front panel. 
22. Fill the dispenser bin one quarter full of ice or start the 

ice machine, allowing the ice machine to drop at least 

three complete batches of ice.

23. Test the ice dispensing action of the dispenser. 

Installation Checklist

Dispenser and ice machine are level?

Drains are vented?

Dispenser does not sit in direct sunlight?

Dispenser does not sit in direct airflow from a heating 

duct?

Bin and ice machine drains are separate?

Ice dispensed properly?

Dispenser is accessible for servicing?

The warranty card was returned?

Ice Machine ice thickness control is properly set?

Owner was instructed on the operation of the 

dispenser?

Owner knows how to clean and sanitize the dispenser?

Owner knows how often to clean and sanitize the 

dispenser?

Owner has your telephone number to call for follow-up 

service on the dispenser?

You have placed one of your service stickers on the 

dispenser for follow-up service?

Summary of Contents for S160 Series





























Reviews: