manualshive.com logo in svg

Manitowoc RF1200W, Technician'S Handbook

Share
Download
Manitowoc RF1200W Technician'S Handbook Download Page 51

Part Number 000007661 6/13

51

Step 5   

Refer to chart below:

Premix cleaner with lukewarm water in a 

non-metallic container.

Step 6   

Remove all water from the evaporator and 

water reservoir. Add the entire cleaner/water solution 
and re-install the reservoir cover.

Leave the cleaner/water solution in the evaporator 
for a minimum of 4 hours.
Step 7   

Remove all cleaner/water from the evaporator 

and water reservoir. 

Step 8   

Follow the standard cleaning and sanitizing 

procedures.

Model

Water 

Reservoir 

Capacity

Mix Cleaner and Water

Use Ice machine nickel safe 

cleaner, part number 

000000084 only

Cleaner

Water

RF0244

RNS0244

RF0266

RNS0308

RF0385

RNS0385

RF0388
RF0399 
RF0644

14 oz (400 ml)

9 oz (266 ml)

5 oz (148 ml)

RF0300

RNS0308

RF0650

17 oz (500 ml) 11 oz (325 ml)

6 oz (177 ml)

RF1200

RFS1200

34 oz (1 L)

23 oz (680 ml)

11 oz (325 ml)

RF2300

RFS2300

68 oz (2 L)

46 oz (1.3 L)

22 oz (650 ml)

Summary of Contents for RF1200W





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands