manualshive.com logo in svg

Manitowoc RF1200W, Technician'S Handbook

Share
Download
Manitowoc RF1200W Technician'S Handbook Download Page 149

Part Number 000007661 6/13

149

CONTROL BOARD ERRORS

The control board monitors the following:

Low water

Gear motor amperage

High pressure

Clogged drain

There are two different errors - Soft errors and hard 
errors. 

•

Soft errors can be reset by cycling power on/off. 

•

Hard errors can not be cleared by cycling power 
on/off and must be reset by pressing the control 
board reset button.

LO WATER - WATER LEVEL IS BELOW LOW 
WATER SENSOR FOR MORE THAN 120 SECONDS

Soft Error

The control board stops the ice machine, energizes 
the Lo Water & Service lights and leaves the water 
solenoid energized. When water contacts the low 
water probe the ice machine will resume ice making.

Hard Error

The water level sensor has 4 probes and the 2 longest 
probes reach to the bottom of the water reservoir. 
When no water is sensed on these probes within 60 
seconds of power up (or the water level sensor is 
disconnected or shorted) the control board stops the 
ice machine and energizes the Lo Water light. The ice 
machine must be reset by pressing the control board 
reset button.

Summary of Contents for RF1200W





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands