Manitowoc Q 1800 Installation And Use Manual Download Page 24

Page: 24 / 28

Maintenance

Section 4

4-8

Water Distribution Tube

Disconnect the water hose from the distribution
tube.

Water Distribution Tube Removal

Loosen the two thumbscrews, which secure the
distribution tube.

Lift the right side of the distribution tube up off
the locating pin, then slide it back and to the
right.

CAUTION

Do not force this removal. Be sure the locating pin
is clear of the hole before sliding the distribution
tube out.

Disassemble for cleaning.
A.

Twist both of the inner tube ends until the
tabs line up with the keyways.

Pull the inner tube ends outward.

Water Distribution Tube Disassembly

Water Curtain

Gently flex the curtain in the center and remove it
from the right side.

Water Curtain Removal

Slide the left pin out.

SV1620

SV1211

THUMBSCREW

DISTRIBUTION

TUBE

THUMBSCREW

LOCATING PIN

INNER

TUBE

INNER

TUBE

KEYWAY

TAB

1. LIFT UP
2. SLIDE BACK
3. SLIDE TO RIGHT

STEP 1

STEP 2

SV1213

Summary of Contents for Q 1800





























Search results

Summary of Contents for Q 1800

Reviews:

Related manuals for Q 1800

Brands by name

Popular brands

Manitowoc Q 1800, Installation And Use Manual

Search results

Summary of Contents for Q 1800

Reviews:

Related manuals for Q 1800

Brands by name

Popular brands