background image

7

Wiring Information

Cables and Wiring

Excellent locations to run cables include:

• Roof 

space

• 

False ceilings/ bulkhead area

• 

Through and/or around external walls

• Under 

fl oors (subject to access being available)

• 

Underground in conduit

 

NOTE: Keep Intercom cables far from any AC wiring. Avoid running 
intercom cable in parallel to AC or any other type of wiring. Avoid placing 
joins or splices in cables. Locate cables where there is access for future 
servicing.

Maximum Length for Cable Runs

The system can be “home-run wired” from a central point or 
“daisy chained” from station to station. However, the number 
of stations on a daisy chain run governs the overall length 
of the run. The tables below show the relationship between 
the length on a cable run and the number of room stations 
permitted and the maximum cable run to a Door Station. 

 

NOTE: The tables are based on the use of Cat-5 or Cat-6 cable. Where 
required, the wire lengths maximum distances can be doubled by 
running 12 AWG speaker wire in parallel with the POS & NEG wires. It 
is important that the POS and NEG wires are balanced in terms of the 
type of wire and the number of wires being used - i.e. if a Cat-5 wire and 
12 AWG speaker wire are being used for the positive connection, a Cat-5 
wire and a 12 AWG speaker wire should also be used for the negative 
connection.

MAXIMUM CABLE LENGTH TO ROOM STATIONS 

NUMBER OF STATIONS ALLOWED

100 yards

1 Room Station

50 yards

2 Room Stations

33 yards

3 Room Stations

25 yards

4 Room Stations

Cable Type and Confi guration

The general intercom functions for VMC1 can be cabled using 
Cat-5 or Cat-6 cables. If required, 6-conductor telephone 
cables can be used provided the system is confi gured  for 
6-wire operation. 

Be sure to clearly tag all cables to identify any damaged cables 
or other system faults. See the table below for Cat-5 wire color 
recommendations.

ROOM STATIONS SHOULD
BE AT LEAST TEN FEET
APART FROM ONE 
ANOTHER

MAXIMUM CABLE LENGTH TO DOOR STATIONS

NUMBER OF STATIONS ALLOWED

80 yards

1 Door Station

MASTER STATION CONNECTION

VIDEO DOOR STATION

NON-VIDEO DOOR STATION

ROOM STATION

WIRING

POS

Green White

Green White

Green White

Cat-5/6

NEG

Green

Green

Green

TC

Orange White

Orange White

Orange White

VLC

Orange

VLCx

Orange

Orange

COM1

Blue White

Blue White

Blue White

COM2

Blue

Blue

Blue

MUS1

Brown White

MUS2

Brown

VIDx

Signal

GND

Ground

AUX

Yellow

Optional

Optional Video Signal

Brown White

Cat-5/6

Optional Video Ground

Brown

Summary of Contents for VMC1

























Reviews: