manualshive.com logo in svg

M&G DuraVent DuraStack PRO DAS1, Installation And Maintenance Instructions Manual

Share
Download
M&G DuraVent DuraStack PRO DAS1 Installation And Maintenance Instructions Manual Download Page 9

Flue 

Diameter Ø

(in)

Number of tube 

per Joint

5 to 10

1/5

11 to 16

1/4

18 to 22

1/3

24 to 28

1/2

30 to 36

2/3

32 to 36

3/4

TABLE 6 -

 Expected number of 

Tubes per Joint Assembly

 (for S-2000, S-650 or S-375) 

SEALANT USAGE 

1.  

Part No. S-2000:

 a high temperature pre-mixed sealant for flue gas temperature up 

to 2000°F. S-2000 IS WATER SOLUBLE AND SHOULD NOT BE USED WHERE EXPOSED 
TO WEATHER

2.  

Part No. S-650

 (Permatex® Red High Temp Silicone) is red and is one of 

our UL approved sealants for temperatures up to 650°F. Can also be used for 
weathering/sealing on outdoor seams & Channel Bands where necessary. 

3.  

Part No. S-375

 (Nuflex 302 General Purpose) is a low temperature grey silicone 

(450°F) only for weathering/sealing on outdoor seams & Outer Band BSE where necessary. 

CAUTION: 

-  THE OUTER BAND 

(BSE)

 IS DESIGNED TO SLIDE ON THE OUTER WALL. DO NOT 

ATTACH BY SCREWS INTO THE OUTER CASING. 
 
-  DO NOT ALLOW SCREWS TO PENETRATE THE INNER PIPE. THIS CAN CAUSE 
CORROSION, GAS LEAKAGE OR EXPANSION FAILURE. 
 
-  NEVER USE SCREWS THROUGH THE OUTER JACKET OF A BELLOW LENGTH

9

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  

Figure 11 - Joint Assembly Step 6  

STEP 6 (DIS PRO and DAS PRO only) 

Secure the Outer Casing with the Outer  Band (

BSE

). 

Joint installation is now complete.

NOTE:

 Seal the 

BSE

 band with

  

S-375

 sealant if exposed to weather.

Summary of Contents for DuraVent DuraStack PRO DAS1




































Reviews:

No comments

Brands by name

Popular brands

Load more brands