Mamas & Papas Primo Viaggio I.P., Instructions For Safe Use

Page: 9 / 12

9
body without constricting him/her too much. Check that the
harness is not twisted and that the child does not release it.
• The safety seat is not a substitute for a cot and if the child
needs to sleep it is important to lie him/her down.
• Do not leave the car safety seat in the car exposed to the sun.
Some parts might heat up and be harmful to the delicate skin
of the child -check before placing the child in the seat.
• Do not use the safety seat without its fabric covering, which
cannot be replaced with one not approved by the manufacturer
since it is an integral part of the safety seat and the safety system.
• If in doubt refer to the manufacturer or retailer of the safety seat.
• Do not remove the adhesive and stitched labels since
this might make the product non compliant with legal
requirements.
• Do not use the safety seat if it has signs of breakage or
missing parts, is second hand, or if it has been subjected to
violent stress in an accident, because it might have suffered
extremely dangerous structural damage.
• Do not modify the product.
• For any repairs, replacement parts and information about the
product, contact the after-sales assistance service. Contact
information is provided on the last page of this manual.
• Do not use this car safety seat after five years from the
date of production indicated on the structure. The natural
ageing of the materials may mean that it is no longer
compliant with standards.
• The use of the safety seat for premature infants born at
less than 37 weeks could cause respiration problems for
the infant seated in the safety seat. It is advisable to seek
medical advice before leaving the hospital.
• Do not use accessories not approved by the manufacturer
or by the competent authorities.
WARNING: FOR USE AS A RECLINER.
•
Do not use the reclined cradle once your child can sit
unaided.
•
This reclined cradle is not intended for prolonged
periods of sleeping.
•
It is dangerous to use this reclined cradle on an
elevated surface, e.g. a table.
Instructions for use
1• "Primo Viaggio I.P." is provided with the Surefix System for
in-car attachment and detachment from an "Isofix Base" or
"Adjustable Base" and outside the vehicle to Mamas & Papas
strollers and chassis. To attach "Primo Viaggio I.P." (to an "Isofix
Base", "Adjustable Base", or Mamas & Papas stroller or chassis)
align it with the attachment points and push down with
both hands until it clicks into place.
2• To release "Primo Viaggio I.P." (from an "Isofix Base",
"Adjustable Base", or Mamas & Papas stroller or chassis) raise
the handle to the transport position, push the lever on the
backrest upwards and at the same time raise the safety seat.
3• To engage the safety harness, put the two shoulder straps
on and insert them into the buckle of the crotch strap until
they click into place.
4• To release the safety harness press the red button on the
crotch strap buckle.
5• To slacken the harness shoulder straps press the metal
button in the centre of the safety seat and simultaneously
pull the shoulder straps towards you.
6• To tighten the shoulder straps on the child, pull the central
adjustment strap towards you as shown in the figure,
taking care not to over-tighten the straps and leaving
minimal room to manoeuvre.
7• The shoulder straps of the safety harness and the “Side Impact
Protection” headrest can be adjusted simultaneously to 5
different heights so as to follow the growth of the child. To
adjust the height, press the rear height adjustment button
(on the safety seat backrest) and at the same time raise or
lower to the required position, ensuring that it clicks into
place. Slacken the shoulder straps before adjusting the
height of the safety harness and the headrest.
8• The correct position of the headrest is defined by the correct
position of the shoulder straps. The child’s shoulders must be
just above the point of passage of the shoulder straps.
9• The seat is equipped with an anatomic padded cushion for
newborns, to be removed when the child is older.
10• The safety seat handle has four fixed positions. To rotate it press
the two round buttons on the handle and simultaneously
move it to the required angle. Ensure it clicks into position.
• Position A: the in-car position; Position B: the position for