Pre - Assembly
● Thread Hand Knob into Part H (Bike Arm Bar) (approx. 10 turns to the right). Repeat for the remaining 7 Bike
Arm Bars and set them to the side.
Assembly
Pre - Assembly:
1. Unload all contents from box and check to make sure all parts and components are present.
2. Thread Knob into Part H (Bike Arm Bar) (approx. 10 turns to the right). Repeat until all 8 Bike Arm Bars
have Knobs in them. Set these parts to the side.
Assembly:
Step 1:
For this step you’ll need 1 part B, 1 part C, 1 SHCS screw, 1 Cap Nut, Small Hex Key, Large Hex Key
.
Attach part C to part B using 1 SHCS screw,and 1 Cap Nut. Line up Part C to Part B as shown in picture below.
Next insert the Cap Nut into back side of part B and hold in place with fingers. Finally, Run SHCS screw into
Part C and into Cap Nut located inside Part B. Tighten by hand and use hex keys as needed to tighten.
Repeat with other Part B and Part C.
DO NOT TIGHTEN ALL THE WAY YET – JUST SNUG.
Step 2:
For this step you’ll need 1 part G, 1 bolt, 1 washer,1 nut, and one of the assembled parts B/C you just
created from steps above.
We will now attach Part G to part B using 1 bolt ,1 washer and 1 nut. The Bolt will run through part C, through
part B, through part G, through the washer, and then we’ll attach the nut onto the bolt and hand tighten. See
pictures below for clarification.
Step 1:
For this step you’ll need 1 part B, 1 part C, 1 SHCS screw, 1 Cap Nut, Small Hex Key, Large Hex Key.
● Attach part C to part B using 1 SHCS screw,and 1 Cap Nut. Line up Part C to Part B as shown in picture
below.
● Next insert the Cap Nut into back side of part B and hold in place with fingers. Finally, Run SHCS screw into
Part C and into Cap Nut located inside Part B.
● Tighten by hand and use hex keys as needed to tighten.
● Repeat with other Part B and Part C.
DO NOT TIGHTEN ALL THE WAY YET – JUST SNUG.
Pre - Assembly:
1. Unload all contents from box and check to make sure all parts and components are present.
2. Thread Knob into Part H (Bike Arm Bar) (approx. 10 turns to the right). Repeat until all 8 Bike Arm Bars
have Knobs in them. Set these parts to the side.
Assembly:
Step 1:
For this step you’ll need 1 part B, 1 part C, 1 SHCS screw, 1 Cap Nut, Small Hex Key, Large Hex Key
.
Attach part C to part B using 1 SHCS screw,and 1 Cap Nut. Line up Part C to Part B as shown in picture below.
Next insert the Cap Nut into back side of part B and hold in place with fingers. Finally, Run SHCS screw into
Part C and into Cap Nut located inside Part B. Tighten by hand and use hex keys as needed to tighten.
Repeat with other Part B and Part C.
DO NOT TIGHTEN ALL THE WAY YET – JUST SNUG.
Step 2:
For this step you’ll need 1 part G, 1 bolt, 1 washer,1 nut, and one of the assembled parts B/C you just
created from steps above.
We will now attach Part G to part B using 1 bolt ,1 washer and 1 nut. The Bolt will run through part C, through
part B, through part G, through the washer, and then we’ll attach the nut onto the bolt and hand tighten. See
pictures below for clarification.
Step 2:
For this step you’ll need 1 part G, 1 bolt, 1 washer,1 nut, and one of the assembled parts B/C you just
created from steps above.
● We will now attach Part G to part B using 1 bolt ,1 washer and 1 nut. The Bolt will run through part C, through
part B, through part G, through the washer, and then we’ll attach the nut onto the bolt and hand tighten. See
pictures below for clarification.
● Repeat the steps from above to attach part G to the other parts B/C assembly.
● The finished assembly should resemble image.
Repeat the steps from above to attach part G to the other parts B/C assembly. The finished assembly
should resemble image below:
Step 3:
For this step you’ll need the above assembly as well as part D, 2 SHCS screws and 2 cap nuts
.
Line up part D so the mounting holes line up with the holes on the forward legs of the above assembly.
Insert 1 cap nut into back of above assembly mounting hole and hold with finger in place. Next, insert 1
SHCS screw through part D, through above assembly, and into the cap nut. Tighten by hand or with hex
keys as needed.
Step 4:
Aassemble the Part E (Back Stabilizer Bar) to the part C (Back legs),it’s the same way as Step 3.
DO NOT TIGHTEN ALL THE WAY YET – JUST SNUG.