MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
.
Thread the free ends of each strap
down and under the cross bar, and,
back up through the boarding ramp
slot.
See image 13. Note: On some
factory models, the free strap ends
must be threaded back under the
carriers in order reach the cross bars.
. Pull the free end of each strap loop down
until the buckles are positioned half way up
the side of the kayak. Thread each free end
down and through the inside bottom slot in
each carrier. See image 12.
. Thread the free strap ends up and through
the buckles. Pull down to tighten. Dress
any extra strap down and around the cross
bars.
. For MD series: Install the bow & stern safety
lines per the attached instructions.
. Note: Safety tie-downs are required for all
transport.
TM
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
MALONE
R
. Thread the free ends of each strap down and under
the cross bar, and, back up through the boarding ramp
slot. See image 13.
. En tirant vers le bas, faites passer le bout plat de
chacune des courroies sous la barre transversale, puis
vers le haut, dans la fente située sur la rampe de
chargement. (Figure 13)
. Pull the free end of each strap down until the buckles are
positioned half way up the side of the kayak. Thread each
free end down and through the inside bottom slot of each
carrier. See image 12.
. Tirez sur le bout plat de chacune des courroies, vers le bas,
jusqu’à ce que les boucles soient situées à mi-hauteur sur le
côtédu kayak. En tirant vers le bas, faites passer l’extrémité
de chacune des deux courroies dans la fente inférieure de leur
support respectif. (Figure 12)
. Thread the free strap ends up and through the buckles. Pull
down to tighten. Dress extra strap down and around the
cross bars. Install the bow & stern safety lines per attached
instructions. See image 14.
. Tirez le bout plat de chacune des courroies vers le haut en les
faisant glisser dans la boucle, puis tirez vers le bas afin de bien
les serrer. Attachez la courroie d’appoint aux barres
transversales. Attachez les filins de sécurité avant et arrière en
suivant les instructions fournies. (Figure 14)
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
Assurez-vous que les pièces de montage, les courroies de fixation et les filins de sécurité soient fixés
correctement lorsque vous transportez un kayak. L’utilisation de ce produit pour un usage autre que le
transport d’un kayak en annule la garantie.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
Installation & Loading Instructions - MPG118MD J-Loader
Instructions - Installation et chargement
TM
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
.
Thread the free ends of each strap
down and under the cross bar, and,
back up through the boarding ramp
slot.
See image 13. Note: On some
factory models, the free strap ends
must be threaded back under the
carriers in order reach the cross bars.
. Pull the free end of each strap loop down
until the buckles are positioned half way up
the side of the kayak. Thread each free end
down and through the inside bottom slot in
each carrier. See image 12.
. Thread the free strap ends up and through
the buckles. Pull down to tighten. Dress
any extra strap down and around the cross
bars.
. For MD series: Install the bow & stern safety
lines per the attached instructions.
. Note: Safety tie-downs are required for all
transport.
TM
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
.
Thread the free ends of each strap
down and under the cross bar, and,
back up through the boarding ramp
slot.
See image 13. Note: On some
factory models, the free strap ends
must be threaded back under the
carriers in order reach the cross bars.
. Pull the free end of each strap loop down
until the buckles are positioned half way up
the side of the kayak. Thread each free end
down and through the inside bottom slot in
each carrier. See image 12.
. Thread the free strap ends up and through
the buckles. Pull down to tighten. Dress
any extra strap down and around the cross
bars.
. For MD series: Install the bow & stern safety
lines per the attached instructions.
. Note: Safety tie-downs are required for all
transport.
TM
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
.
Thread the free ends of each strap
down and under the cross bar, and,
back up through the boarding ramp
slot.
See image 13. Note: On some
factory models, the free strap ends
must be threaded back under the
carriers in order reach the cross bars.
. Pull the free end of each strap loop down
until the buckles are positioned half way up
the side of the kayak. Thread each free end
down and through the inside bottom slot in
each carrier. See image 12.
. Thread the free strap ends up and through
the buckles. Pull down to tighten. Dress
any extra strap down and around the cross
bars.
. For MD series: Install the bow & stern safety
lines per the attached instructions.
. Note: Safety tie-downs are required for all
transport.
TM
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
MALONE
R
. Thread the free ends of each strap down and under
the cross bar, and, back up through the boarding ramp
slot. See image 13.
. En tirant vers le bas, faites passer le bout plat de
chacune des courroies sous la barre transversale, puis
vers le haut, dans la fente située sur la rampe de
chargement. (Figure 13)
. Pull the free end of each strap down until the buckles are
positioned half way up the side of the kayak. Thread each
free end down and through the inside bottom slot of each
carrier. See image 12.
. Tirez sur le bout plat de chacune des courroies, vers le bas,
jusqu’à ce que les boucles soient situées à mi-hauteur sur le
côtédu kayak. En tirant vers le bas, faites passer l’extrémité
de chacune des deux courroies dans la fente inférieure de leur
support respectif. (Figure 12)
. Thread the free strap ends up and through the buckles. Pull
down to tighten. Dress extra strap down and around the
cross bars. Install the bow & stern safety lines per attached
instructions. See image 14.
. Tirez le bout plat de chacune des courroies vers le haut en les
faisant glisser dans la boucle, puis tirez vers le bas afin de bien
les serrer. Attachez la courroie d’appoint aux barres
transversales. Attachez les filins de sécurité avant et arrière en
suivant les instructions fournies. (Figure 14)
12
14
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
Assurez-vous que les pièces de montage, les courroies de fixation et les filins de sécurité soient fixés
correctement lorsque vous transportez un kayak. L’utilisation de ce produit pour un usage autre que le
transport d’un kayak en annule la garantie.
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: [email protected]
Installation & Loading Instructions - MPG118MD J-Loader
Instructions - Installation et chargement
TM
. With the carriers in the UP position. Gently push down
on the release pins. They will automatically stop, lock
in place, and remain fixed. See image 6.
. Lorsque les supports sont relevés, appuyez doucement
sur la goupille de verrouillage. Elle se bloquera
automatiquement et sera ainsi verrouillée. (Figure 6)
. With the carriers in the DOWN position. Gently pull up
on the release pins. Lift and rotate the rear of the carrier
until it stops in the UP position. See image 5.
. Lorsque les supports sont rabaissés, tirez doucement la
goupille de verrouillage vers le haut. Soulevez la partie
arrière du support jusqu’à ce que celui-ci se bloque en
position relevée. (Figure 5)
5
4
6
2
MALONE
R
. Insert a second Mounting Bolt into the top side unused
hex hole and down through the Jawz mounting adapter.
Close the mounting hole cover. Apply a washer and second
T-knob and slightly tighten until the carrier is secure.
Repeat steps 1-4 for the 2nd carrier and rear cross bar.
See image 4.
. Insérez un boulon de fixation dans le second trou hexagonal
situé sur le côté supérieur du support et faites-le passer
dans l’adaptateur Jawz. Vissez un bouton en T à la base du
second boulon, puis serrez légèrement jusqu’à ce que le
support soit bien fixé. Répétez les étapes 1 à 4 pour le
deuxième support et la barre transversale arrière.
(Figure 4)
Installation & Loading Instructions - MPG114MD DownLoader
Instructions - Installation et chargement
TM
Bow and Stern Safety tie-downs are required for all rooftop transport.
Failure to use these safety lines voids all warranty.
If your kit did not include safety tie-downs, we strongly recommend the use of the
Malone MPG316 Sentry Ratchet Tie-Down System or Malone MPG309 SpeedLine Mini Ratchet Tie-Down
