background image

Art. No. 1511001

www.malmsten.com

2

Exclusions and Conditions:

•  Operations, which shall be made by the user and on his cost, such as maintenance of cleanli-

ness, periodical checkups (as in point 2.1)

•  Mechanical and chemical damages caused by improper use and maintenance (i.e. attempts of 

self-repair; lack of maintenances and inspections; using inadequate cleaning agents, adjust-
ments made by the user) 

•  Mechanical damages caused by the excessive burden on the equipment
•  Damages caused by the user or third party (including acts of vandalism) hang, swing or climb 

on the equipment

•  Consumable parts (like nets, net hooks, etc.)
•  Damages caused by operation of the equipment by non-authorized persons
•  Installation of the equipment not performed in accordance with the assembly manual  
•  Damages caused by natural disasters such as floods, fire, wind, lightening or other acts of 

nature 

•  Damages caused by usage not in accordance with equipment destination 

3

Post-warranty Services

3.1 After the warranty expires, it is recommended to order a professional post-warranty service 

performed by the authorized distributor once every 12 months in order to make sure, that the 
equipment is in good condition and can be used safely.

3.2 In case of a failure discovered after the time of warranty, the user might inform the manufactu-

rer or it’s authorized distributor about the problem in the same way which is described in point 
1.4. The manufacturer or distributor will offer a solution to the problem within 7 days. After the 
claim is accepted, both parties will agree on a suitable term of repairs.

LOCATION OF THE SERIAL NUMBER:

The serial number consists of XX/YYYY/ZZZZZ 
where:
XX – calendar week of manufacturing 
YYYY – year of manufacturing 
ZZZZZ – serial number 

Removing the sticker will void the warranty.

Sample view:

Summary of Contents for 1511001















Reviews: