background image

Drying Cabinet 
 
 

Operation, Maintenance and Installation Manual

 

 Issue 15 

Page 

12

 

7

th

 October 2011 

 

 
 

 

A charge will be made for work done or service call where: 

 

There is nothing wrong with the unit. 

 

The defective operation of the unit is due to failure of electricity or water supply. 

 

Defects are caused by neglect, incorrect application, abuse or by accidental damage of the 
unit. 

 

An unauthorised person has attempted to repair the unit. 

 

Harsh environmental situations such as water quality that may cause the water tank damage 
can not be considered warranty. 

 

Claims for damage to contents, carpet, ceilings, foundations or any other consequential loss 
either direct or indirect resulting from, power spikes, incorrect operation, incorrect installation or 
faulty product are excluded. 

 

All warranties are NOT transferable. 

 

Unauthorised use of non-genuine Malmet Parts in units covered by Warranty will void all 
warranty and warranty claims. 

 

To the extent permitted by law Warranty labour (service work) shall not include units located 
outside of city metropolitan areas and costs outside these areas shall be borne by the 
Customer.  The Customer shall be notified of this prior to the warranty call out. 

Warranty on Replacement Parts 

Parts replaced under warranty are warranted for the balance of the original warranty period for that 
product. 
 

Unit Components 

Parts 

Labour 

Structural Guarantee 

All other components 

 

 

Date Sold:  ...................................  

Warranty Expiry Date:  ...................................  

 

Sold To: 

For Service Contact: 

 

 

 

 

 

 

 

Summary of Contents for Drying Cabinet















Reviews: