background image

·  Rest the door on a soft surface;

 

· 

To replace the door, repeat the above steps in reverse order. 

 

 

 

 

 
Removing the Inner Pane of Glass

 

 

· 

Double oven door:

 Remove the seal G by unscrew the no.2 bolts

 (fig.1) 

· 

Gently pull out the inner pane of glass(fig.2) 

· 

Clean the glass with an appropriate cleaner. Dry thoroughly, and place on a soft 
surface. 
Now you can also clean the inside of the outer glass. 
 

 

 

Replacing the Oven Lamp

  

·

 

 Disconnect the oven from the power supply by means of the omni polar switch used to 

connect the appliance to the electrical mains ;or unplug the appliance if the plug is 
accessible ; 

·

  Remove the glass cover of the lamp-holder ; 

·

  Remove the lamp and replace with a lamp resistant to high temperatures (300

)with 

the following characteristics: 

 



Voltage: 220-240V   



Wattage: 25W       



Type: E 14    

      
 

·

  Replace the glass cover and reconnect the oven to the mains power supply . 

Warranty & Service 
FAQs and Troubleshooting 

What should I do if the oven doesn’t heat up? 
Check to see if one of the following actions resolves the issue: 
●  The oven may not be switched on. Switch the oven on. 
●  The clock may not be set. Set the clock (see section “Setting the clock”). 
●  Check to see if the required settings have been applied. 
●  A household fuse may have blown or a circuit breaker may have tripped. Replace the 

fuses

 or reset the circuit. If this happens repeatedly, call an authorised electrician. 

  

Summary of Contents for MDO-80BL

















Reviews: