Malibu Boats 258/6890 Assembly Instructions Manual Download Page 2

Safety and Care Advice

Important -

 Please read these instructions fully before starting assembly

• 

Warning:

 This unit weighs 

approximately 101kgs.

Please lift with care.

• Check you have all the

components and tools listed on 

pages 1, 2 and 3.

• Remove all fittings from the 

plastic bags and separate them 

into their groups.

• Keep children and animals 

away from the work area, small 

parts could choke if swallowed.

• Parts of the assembly will be 

easier with 2 people.

• Make sure you have enough 

space to layout the parts before 

starting.

• Do not stand or put weight on 

the product, this could cause 

damage.

• Assemble the item as close to 

its final position (in the same 

room) as possible.

• Assemble on a soft level 

surface to avoid damaging the 

unit or your floor (use opened  

out unit carton).

1

Care and maintenance

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

• From time to time check that 

there are no loose screws on 

this unit.

• This product should not be 

discarded with household 

waste. Take to your local

authority waste disposal centre.

• We do not

recommend the 

use of power 

drill/drivers 

for 

inserting screws

,

as this could damage the unit.

Only use hand screwdrivers.

• 

Safety note:

 It is

recommended that this unit is 

secured to a wall using the 

bracket supplied.

• Dispose of all packaging 

carefully and responsibly.

Components - 

Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the 

Customer Helpline: 08456 400800 

quoting the reference 

numbers below

1

6

7

5

2

Top

 

(D2851A)

(1423 x 494mm)

Base

 

(D2856A)

(1423 x 494mm)

Drawer Front

 

(D2783A)

(710 x 156mm)

 x 3

Drawer Base

(T693-367)

(693 x 367mm)

 x 3

Left Drawer

Side 

(W370-124LH)

(370 x 124mm)

 x 3

Right Drawer

Side 

(W370-124RH)

(370 x 124mm)

 x 3

3

Drawer Back 

(W682-124LH)

(682 x 124mm)

 x 3

80%

80%

90%

80%

4

Ruler

 -

 Use this ruler to help correctly identify the screws

mm 10

20

30

40

50

60

70

80

90 100 110 120 130 140 150 160 170

Summary of Contents for 258/6890

























Reviews: