background image

12

Specifications

MO15 Receiver (Rx)

Colour: red
Weight: 136g including batteries, 67g without batteries 
Dimensions: length: 91mm  width: 72mm  depth: 26mm
Battery: 3 x AA alkaline. Observe correct polarity and clean contacts when
replacing batteries.
ON/OFF: sliding switch on side
Volume: volume control wheel on the side. Turn up to increase and down to
decrease. Reset button on the top will not reset if Tx is active. Press button and
hold for 3 seconds to cancel active LED. Do not use ON/OFF button to reset the
receiver.
Green LED: flashes once every 2 seconds when Rx is ready for use. Red LED 1
to 7: ON when paired Tx is triggered. Up to 7 Txs can be tuned and paired to
the 7 LEDs. Once an LED is activated, even paired ON, when reset, it will not be
triggered again for 2 minutes. The LED and buzzer will be reactivated if the
linked Tx remains active.
Tuning point: 2 small pin holes on the back of the Rx. The one on the left is the
tuning hole. Insert the straight end of a paper clip into the hole and press
slightly then release, all the red LEDs will glow. While the red LEDs are on,
activate the Tx. The LEDs will go off and only the LED which has been selected
on the Tx will flash. When the Tx is activated again, the LED will flash and the
buzzer will sound. Green LED will flash rapidly when battery capacity is low.
Replace battery.
Default hole: the small hole on the right on the back of the Rx is the default
hole. Insert the straightened end of a paper clip and press gently then release.
This will erase all the tuned memory. Re-tuning to the Tx/s will be required.
Model: MO15 (Rx)
Standard:         and   

Sensors

Easy-Clip

©

: Length 79 cm. Keep lever up when not in use. Clean sensor regularly.

Standard:  Length 79 cm. Keep clean and wipe dry. The sensor plate and
crocodile clip MUST NOT be in direct contact with the skin. 
Bed-Mat: 54 x 42 cm. Wire length 202 cm. Keep clean and wipe dry. Always
cover with cotton sheet as well as a bath towel. Under no circumstances should
the transmitter (Tx) be attached to user’s clothing when used with a Bed-Mat.
Wander-Mat: 75 x 40 cm. Wire 150 cm.  Use pressure on or pressure off (for
pressure off use with ‘inverter’).
Dialysis-Mat: 22 x 17 cm. Wire 100 cm. Keep clean and wipe dry.

Malem Medical reserves the right to change specifications without prior notice. 
©2011 Malem Medical

6492 Master IBooklet 061010_Master IBooklet 061010  21/01/2011  14:45  Page 14

Summary of Contents for Universal MO15

























Reviews: