background image

4 | 

P a g e

 

 

 

-

 

The Easy-Clip is the sensor of the alarm unit and consists of the sensor, the sensor wire and the 

plug: 
 

 

 

 

o

 

To connect: Insert the 

plug

 into the alarm socket making sure the Easy-Clip sensor lever is 

lifted up, otherwise the alarm will start sounding. 

Do not unplug the wire from the alarm 

unit unless for cleaning or replacement

, otherwise this part will break.  

o

 

To use, lift sensor clip 

lever

, attach sensor to the outside of close fitting underwear, at the 

location most likely to get wet first, by inserting material inside the sensor jaws at the front 

and closing the lever. Dispose of insulating tag if present.  Lowering the lever without any 

dry material in the jaws will trigger the alarm and prevent the alarm from resetting. Lift the 

lever and press the reset button. DO NOT force the lever in the wrong direction. 

 

 

o

 

To 

clean

 the sensor: The construction of the Easy Clip doesn’t allow it to be taken apart. 

After wetting, the clip can be cleaned by rinsing under the tap and dried with a piece of 

kitchen  towel  and  then  is  immediately  ready  for  re-use.  Intermittently  clean  with  soapy 

water or a mild detergent and an old tooth brush and rinse to remove any “fluff” material 

from the jaws of the Easy-Clip to prevent the alarm from being reset. 

See video page 16

o

 

The 

wire

  between  the  sensor  and  the  plug  and  alarm  unit  is  79  cm  long  and  is  an 

important part of the whole alarm unit. The wire is sufficiently flexible to be comfortable in 

use  but  sufficiently  robust  to  ensure  long  life.  It  will  not  however  tolerate  abuse,  being 

bitten  or  chewed.  DO  NOT  USDE  THE  WIRE  TO  PULL  THE  SENSOR  OUT  OF  THE 

UNDERWEAR – ALWAYS UNDO THE CLIP.  Do not unplug the sensor from the body worn 

alarm.  

 

-

 

The alarm unit contains the alarm's electronics, chip, buzzer, battery, settings panel and LED.  

 

 

 

 

 

 

o

 

Connection:

  The  alarm  unit  is  connected  to  the  child  pyjama  top  with  the  pyjama  top 

gripper

 on the alarm. Secure it on the pyjama top or night dress, close to the shoulder or in 

the  breast  pocket  if  available.  Thread  the  cord  inside  top  as  shown  below.  For  small 

Summary of Contents for Deluxe MO24

















Reviews: