manualshive.com logo in svg

Malcotools FasGroov FGVK, Instruction

Share
Download
Malcotools FasGroov FGVK Instruction Download Page 9

w w w . m a l c o t o o l s . c o m

SHIPLAP FABRICATION

#1
GRAY

#2/4
DARK
ORANGE

#2/4
DARK
ORANGE

#3
ORANGE

#5
BLUE

W1

H1

W2

H2

Face the factory made female shiplap edge of a 
ductboard section. Place the FasGroov #1 Tool 
against the left edge of the ductboard. Push the 
FasGroov #1 Tool closely along the left edge to 
produce a female shiplap groove.

Set the FasGroov Square on top of the duct-
board. Place the ruled edge along the factory 
made female shiplap edge. Measure the desired 
inside duct width dimension (W1) and align with 
the right edge of cut made previously by the 
FasGroov #1 Tool. Place the FasGroov #24 Tool 
against the slide edge and push along to produce 
a right hand shiplap groove.
Move the FasGroov Square to the right and mea-
sure the desired inside duct height dimension 
(H1). Align dimension with the right edge of cut 
previously made by the FasGroov #2/4 Tool.

#1  TOOL

#2/4 TOOL

#3 TOOL

CUT FLAP

9

Summary of Contents for FasGroov FGVK













Reviews:

No comments

Brands by name

Popular brands

Load more brands