Malaguti CIAK MASTER 50-4T Electric System Troubleshooting Download Page 30

Page: 30 / 31

10.05

CHAPTER

PAGE

ISSUE

ELECTRIC SYSTEM TROUBLESHOOTING

ENGLISH

SECTION 2

Signalling system

SECTION 2

- TROUBLESHOOTING

3.4 Checking voltage level

- Connect

Tester (DC 20 V)

to horn (3), as follows:

- Terminal (+) of tester

Blue cable (1).

- Terminal (-) of tester

Chassis grounding (2).

- Turn key “ON”.

Value read must be

12 V.

NOT COMPLIANT

- Blue cable between key switch and
horn is interrupted.

- Repair (see wiring diagram).

COMPLIANT

- Orange cable between left hand switch and horn is
interrupted.

- Repair.
- See “Wiring Diagram”.

- Fuel probe is faulty.

- Replace.

INDICATOR HAND ON

INSTRUMENT BOARD

DOES NOT MOVE

INDICATOR HAND IS POINTING TO “FULL” (1)

4. FUEL LEVEL INDICATOR IS NOT WORKING

4.1 Fuel probe

- Detach connector of probe.

- Provide jumper (1) between white/green cable and black
cable of three-way connector of wiring.

Summary of Contents for CIAK MASTER 50-4T
































Search results

Summary of Contents for CIAK MASTER 50-4T

Reviews:

Related manuals for CIAK MASTER 50-4T

Brands by name

Popular brands

Malaguti CIAK MASTER 50-4T, Electric System Troubleshooting

Search results

Summary of Contents for CIAK MASTER 50-4T

Reviews:

Related manuals for CIAK MASTER 50-4T

Brands by name

Popular brands