manualshive.com logo in svg

Mäktig 710035, Owner'S Manual, Page: 10 / 10

Share
Download
Mäktig 710035 Owner'S Manual Download Page 10

10 

 

8.  TROUBLESHOOTING 

 

Problem Cause

Solution

Jumpstarter 
can not jump 
start vehicle   

The internal battery in the 
jumpstarter is not fully 
charged  

Charge for at least 28 hours 

The jumpstarter’s battery 
has been damaged   

Replace jumpstarter battery 

Jumpstarter 
does not 
recharge 

Accessories connected to 
12V DC socket 

Disconnect accessories 

110V AC charger 
damaged 

Replace 110V AC charger 

Not charged after 
previous use 

The battery could possibly be 
damaged due to not been 
recharged after previous uses. 

Plug-in 
appliance does 
not work 
 

Battery has discharged to 
10V 

Recharge the jumpstarter 
 

Fuse blown 

Replace fuse 

The appliance power is 
over standard. 

Use an appliance the power is 
lower than standard. 

 
 

 

9.  SPECIFICATIONS 

 

Boost Ampere 

800 instantaneous cranking amps 

Battery   

Max22Ah Sealed Lead-acid Battery 

Adapter 

110V AC/13.5V DC/500mA 

Jump start cables (size/length) 

4AWG/1m 

Cigarette lighter plug maximum 
current 

15A 

Output voltage 

12V DC 

Dimensions L*W*H 

11.42*7.29*9.1inch (290*185*231mm

）

Weight 16.5lb/7.5kg 

 
 

Summary of Contents for 710035











Reviews:

No comments