background image

 

 

1.  CUTTER ALIGNMENT 

The  horizontal  alignment  of  the  cutter  was  did  at  the 

factory, however, for possible adjustments, using the key 

13  (8),  loosen  the  screw  of  the  eccentric  washer  and 

turn it until the cutter shaft center is aligned to the line of 

surface the sliding guide of the table: 

 

The  vertical  cutter  alignment  should  be  performed 

always  the  router  is  mounted  on  the  swinging  support, 

noting  that  the  ends  of  the  knives  should  exceed  about 

1.5 mm in front of the frontal guide: 

 

 

 

 

 

2.  ADJUSTING THE SPRING OF SCRAPER BLOCK 

The  spring  tension  of  the  scraper  block  copier  is  set  at 

the factory, but for any adjustments using the key 13 (8). 

Must loosen the lower nut shown in the figure below and 

rotating the screw clockwise to increase the tension and 

counter-clockwise to decrease tension. Retighten the nut. 

Obs.:  This  tension  is  applied  pressing  the  wheel  copier 

of  scraper  block  over  the  panel  surface  to  reproduce  it, 

ensuring true position of the cutter along the edge. 

 

 

3. ADJUSTING THE SCRAPER BIT 

The Scraper Bit  has a special function to reproduce  the 

final  finish  along  the  edges  of  the  tape  with  a  slightly 

rounded  contour,  therefore,  must  be  carefully  adjusted 

according to the following procedure: 

 

Summary of Contents for RBB.1000












Reviews: