background image

WARNING: 

DO NOT let comfort or familiarity with product 
(gained from repeated use) replace strict adherence 
to safety rules for the subject product. 
MISUSE or failure to follow the safety rules stated in 
this instruction manual may cause serious personal 
injury. 

USD302-1 

Symbols 

The followings show the symbols used for tool. 

 volts 

 direct 

current 

 no 

load 

speed 

  revolutions or reciprocation per minute 

  number of blow 

ENC007-8 

IMPORTANT SAFETY 
INSTRUCTIONS 
FOR BATTERY CARTRIDGE 

1. 

Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.

2. 

Do not disassemble battery cartridge. 

3. 

If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion. 

4. 

If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.

5. 

Do not short the battery cartridge: 

(1) 

Do not touch the terminals with any
conductive material.

(2) 

Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc. 

(3) 

Do not expose battery cartridge to water
or rain. 

A battery short can cause a large current flow, 
overheating, possible burns and even a 
breakdown. 

6. 

Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50

C (122

F).

7. 

Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

Follow your local regulations relating to
disposal of battery.

SAVE THESE INSTRUCTIONS. 

Tips for maintaining maximum battery life 

1. 

Charge the battery cartridge before
completely discharged. 
Always stop tool operation and charge the
battery cartridge when you notice less tool
power. 

2. 

Never recharge a fully charged battery
cartridge. 
Overcharging shortens the battery service life.

3. 

Charge the battery cartridge with room
temperature at 10

C - 40

C (50

F - 104

F). 

Let a hot battery cartridge cool down before
charging it. 

4. 

Charge the battery cartridge once in every six
months if you do not use it for a long period
of time.

Summary of Contents for XST01Z











Reviews: