Makita XRM02 Instruction Manual Download Page 7

The following tables indicate the operating time on a single charge.

: Cluster Battery
: Slide Battery

Note: Table regarding to the battery operating time above is for reference. The actual operating time may differ with the 
type of the battery, charging condition, or usage environment.

3-1.

Installing or removing Slide battery cartridge 

(Fig. 4)

• To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 
it into place. Always insert it all the way until it locks in 
place with a little click.

• If you can see the red indicator on the upper side of the 

button, it is not locked completely. Install it fully until the 
red indicator cannot be seen. If not, it may accidentally 
fall out of the tool, causing injury to you or someone 
around you.

• Do not use force when installing the battery cartridge. If 

the cartridge does not slide in easily, it is not being 
inserted correctly.

• To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge or 
pressing the buttons on both sides of the cartridge.

3-2.

Installing or removing Cluster battery cartridge 

(Fig. 5 - 9)

• Pull the supporting bar to allow the battery to insert to

the terminal.

• To insert the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 
it into place.

• Release the supporting bar.
• To remove the battery cartridge, pull the supporting bar 

and take the battery out of the terminal.

4.

Return the battery compartment locker to the original 
position.

5.

Reduced power, distortion and a “stuttering sound” or 
low battery sign 

 that appears on the display are 

all the signs that the main battery pack needs to 
replace.

Battery Cartridge Voltage

AT SPEAKER OUTPUT= 

50 mW + 50 mW

unit: Hour

7.2 V

9.6 V

10.8 V

12 V

14.4 V

18 V

BL7010

Approx. 7.0

PA09

PA12

PA14

PA18

Approx. 8.0

9050

1250

1450

1850

9051

1251

1452

1852

9100

1200

1420

BL1815

9120

BL1014

1220

BL1415

9100A

1200A

BL1815N

Approx. 10.0

9102

1202

1422

1822

Approx. 12.5

9122

1222

BH1420

9102A

1202A

BH9020

BH1220

BH9020A

BH1200C

9134

1234

1434

1834

Approx. 16.5

BH1427

Approx. 17.0

9135

1235

1435

1835

Approx. 19.0

1435F

BL1830

1235F

BL1430

BH9033

BH1233

BH1433

Approx. 21.0

BH9033A

BH1233C

BL1440

BL1840

Approx. 27.0

 WARNING:

Do not use two main batteries at the same time.

 WARNING:

Do not use two main batteries at the same time.

Summary of Contents for XRM02











Reviews: