background image

22. 

Do not leave the tool running. Operate the tool 
only when hand-held. 

23. 

Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.

24. 

Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care. 

25. 

Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.

26. 

Use only flanges specified for this tool. 

27. 

For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the
wheel is long enough to accept the spindle
length. 

28. 

Check that the workpiece is properly
supported. 

29. 

Pay attention that the wheel continues to
rotate after the tool is switched off. 

30. 

If working place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety. 

31. 

Do not use the tool on any materials
containing asbestos.

32. 

When use cut-off wheel, always work with the
dust collecting wheel guard required by
domestic regulation. 

33. 

Cutting discs must not be subjected to any
lateral pressure. 

SAVE THESE INSTRUCTIONS. 

WARNING: 

DO NOT let comfort or familiarity with product 
(gained from repeated use) replace strict adherence 
to safety rules for the subject product. MISUSE or 
failure to follow the safety rules stated in this 
instruction manual may cause serious personal 
injury. 

USD311-1 

Symbols 

The followings show the symbols used for tool. 

 volts 

 direct 

current 

 rated 

speed 

 no 

load 

speed 

  revolutions or reciprocation per minute 

ENC007-8 

IMPORTANT SAFETY 
INSTRUCTIONS 
FOR BATTERY CARTRIDGE 

1. 

Before using battery cartridge, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery. 

2. 

Do not disassemble battery cartridge. 

3. 

If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion. 

4. 

If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.

5. 

Do not short the battery cartridge: 

(1) 

Do not touch the terminals with any
conductive material.

(2) 

Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc. 

(3) 

Do not expose battery cartridge to water
or rain. 

A battery short can cause a large current flow, 
overheating, possible burns and even a 
breakdown. 

6. 

Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50

C (122

F).

7. 

Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

Follow your local regulations relating to
disposal of battery.

SAVE THESE INSTRUCTIONS. 

Tips for maintaining maximum battery life 

1. 

Charge the battery cartridge before
completely discharged. 
Always stop tool operation and charge the
battery cartridge when you notice less tool power.

2. 

Never recharge a fully charged battery cartridge. 
Overcharging shortens the battery service life.

3. 

Charge the battery cartridge with room temperature 
at 10

C - 40

C (50

F - 104

F). Let a hot battery

cartridge cool down before charging it. 

4. 

Charge the battery cartridge once in every six
months if you do not use it for a long period
of time.

Summary of Contents for XAG04

















Reviews: