background image

Installing or removing depressed center 
grinding wheel/Multi-disc 

1

2

3

007219 

WARNING: 

• 

Always use supplied guard when depressed
center grinding wheel/Multi-disc is on tool. Wheel
can shatter during use and guard helps to reduce
chances of personal injury. 

Mount the inner flange onto the spindle. Fit the wheel/disc 
on the inner flange and screw the lock nut onto the spindle. 
To tighten the lock nut, press the shaft lock firmly so that 
the spindle cannot revolve, then use the lock nut wrench 
and securely tighten clockwise. 

1

2

007220 

To remove the wheel, follow the installation procedure in 
reverse. 

Installing or removing diamond wheel 
(optional accessory) 

CAUTION: 

• 

Always install the wheel guard before installing the
diamond wheel. 

• 

When mounting the wheel ensure that the arrow
(indicating the direction of rotation) on the wheel is
pointing in the same direction as the arrow for
rotation provided on the tool. 

Mount the inner flange onto the spindle so that the side 
of the inner flange with the 7/8" diameter protrusion 
faces the diamond wheel.  Place the diamond wheel 
onto the inner flange making sure the protrusion fits into 
the arbor of the wheel.    Use the lock nut to secure the 
wheel by placing it on the spindle so that the flat side 
faces the wheel and screw the lock nut onto the spindle. 
To tighten the lock nut, press the shaft lock firmly so that 
the spindle cannot revolve, then use the lock nut wrench 
and securely tighten clockwise. 

7/8"

1

2

3

4

011576 

Installing or removing flex wheel 
(optional accessory) 

1
2

3
4

007241 

WARNING: 

• 

Always use supplied guard when flex wheel is on
tool. Wheel can shatter during use and guard
helps to reduce chances of personal injury. 

Follow instructions for depressed center grinding 
wheel/Multi-disc but also use plastic pad over wheel. 
See order of assembly on accessories page in this 
manual. 

Installing or removing abrasive disc 
(optional accessory) 

1

3

2

007240 

NOTE: 

• 

Use sander accessories specified in this manual.
These must be purchased separately. 

Mount the rubber pad onto the spindle. Fit the disc on 
the rubber pad and screw the lock nut onto the spindle. 
To tighten the lock nut, press the shaft lock firmly so that 
the spindle cannot revolve, then use the lock nut wrench 
and securely tighten clockwise. 
To remove the disc, follow the installation procedure in 
reverse. 

1. Lock nut 
2. Abrasive disc 
3. Rubber pad 

1. Lock nut 
2. Flex wheel 
3. Plastic pad 
4. Inner flange 

1. Lock nut 
2. Diamond wheel 
3. Inner flange 
4. Spindle 

1. Lock nut wrench
2. Shaft lock 

1. Lock nut 
2. Depressed 

center grinding 
wheel/Multi-disc

3. Inner flange 

Summary of Contents for XAG01












Reviews: