3
ENGLISH
Models:
LS0714, LS0815, LS1013, LS1016, LS1017, LS1018, LS1019, LS1214, LS1216, LS1219, LS1040, LS1221, LXSL01,
XSL02, XSL03, XSL04, XSL06
Inclusive of models followed by F, L and FL, if any.
Preparation
Note: Check contents of package for the following components. Please inform Makita service center of any part missing in
the package immediately.
• Miter saw stand assembly (1 unit)
• Hex wrench 6 (1 pc.)
• Wrench 13 (1pc.)
• Hex socket bolt M8 x 16 (4 pcs.)
• Hex socket bolt M8 x 30 (4 pcs.)
• Hex bolt M8 x 50 (4 pcs.)
• Flat washer 8 (4 pcs.)
• Wheel 300 (2 pcs.)
• Flat washer 8 (2 pcs.)
• Foot arm (1 pc.)
• Handle (1 pc.)
• Adjusting bolt (2 pcs.)
• Clamping nut M12 (2 pcs.)
Explanation of general view
Symbols
............. Read instruction manual.
............. Maximum allowable loading
CAUTION:
• Read and thoroughly understand this manual and the
instruction manual of the tool you use before
performing the following.
• Before installing a tool on this stand, always switch off
and unplug the tool.
• The stand should be bolted in a stable and level
surface using the right angle brackets provided on two
of four feet.
• Use only with Makita model indicated in the instruction
manual.
• Use only the handle to avoid pinched fingers when
raising or folding the stand.
• Before operating the tool, secure it to stand using bolts.
• Do not use the stand on uneven or unstable surface.
• Do not climb, sit or stand on the stand.
• When setting up the miter saw stand in the upright
position or folding it, be sure to securely keep pressing
the pipe of miter saw stand with your foot until it locks.
• When storing miter saw stand, never lean it against the
wall or the like lengthwise or sideways.
• Never pull the locking lever without holding the handle.
Assembling miter saw stand (Fig. 1)
Assemble parts for miter saw stand as disassembled
parts are packed in the carton box.
(1) Adjusting bolt
Place the stand assembly upright and insert adjusting
bolts (2 pcs.) from the below and secure these bolts
by tightening nuts.
To adjust, turn the adjusting bolts until it reaches floor
so that the miter saw stand can be kept stable.
(2) Wheel 300 (2 pcs.)
Insert the wheels onto the leg B of miter saw stand on
both sides and secure the wheels by tightening hex
socket bolt M8 x 16 (2 pcs.) with washer 8 (2 pcs.)
from upper side.
(3) Foot arm
Insert the foot arm onto the port of the leg B from
upper side and secure it by tightening hex socket bolt
M8 x 16 (2 pcs.) from backside.
(4) Handle
Insert the handle onto the miter saw stand from the
cover side and secure it by tightening hex socket bolt
M8 x 30 (4 pcs.) from the ratchet cover side.
Installing a miter saw on the miter saw
stand: (Fig. 2)
Place a miter saw so that the hole in the miter saw base
overlaps a hole in the label on the miter saw stand table
according to applicable models. Secure the miter saw
stand with hex bolt M8 x 50 (4 pcs.) and flat washer 8
(4 pcs.).
How to use miter saw stand
Setting up: (Fig. 3)
1. Grip the handle and place your foot on the pipe of the
leg A of miter saw stand.
2. Release the locking lever with left hand while pressing
down the handle.
1.
Wheel 300
2.
Foot arm
3.
Handle
4.
Adjusting bolt
5.
Hex socket bolt M8 x 16
6.
Flat washer 8
7.
Leg B
8.
Leg A
9.
Hex socket bolt M8 x 30
10. Hex bolt M8 x 50
11. Locking lever
12. Shift lever
13. Pin 10-60
14. Stopper
15. Extension arm
16. Lever 40
17. Clamping screw M8 x 20
18. Leg pipe 28
(220 lbs.)
100Kg
MAX.
