Makita UB001GZ Instruction Manual Download Page 5

5 ENGLISH

4. 

Under abusive conditions, liquid may be 

ejected from the battery; avoid contact. If con-

tact accidentally occurs, flush with water. If 

liquid contacts eyes, additionally seek medical 

help.

 Liquid ejected from the battery may cause 

irritation or burns.

5. 

Do not use a battery pack or tool that is dam-

aged or modified.

 Damaged or modified batteries 

may exhibit unpredictable behaviour resulting in 

fire, explosion or risk of injury.

6. 

Do not expose a battery pack or tool to fire or 

excessive temperature.

 Exposure to fire or tem

-

perature above 130 °C may cause explosion.

7. 

Follow all charging instructions and do not 

charge the battery pack or tool outside the 

temperature range specified in the instruc

-

tions.

 Charging improperly or at temperatures 

outside the specified range may damage the 

battery and increase the risk of fire.

Electrical and battery safety

1. 

Do not dispose of the battery(ies) in a fire.

 

The cell may explode. Check with local codes for 

possible special disposal instructions.

2. 

Do not open or mutilate the battery(ies).

 

Released electrolyte is corrosive and may cause 

damage to the eyes or skin. It may be toxic if 

swallowed.

3. 

Do not charge battery in rain, or in wet 

locations.

4. 

Do not charge the battery outdoors.

5. 

Do not handle charger, including charger plug, 

and charger terminals with wet hands. 

6. 

Do not replace the battery in the rain.

7. 

Do not wet the terminal of battery with liquid 

such as water, or submerge the battery. Do not 

leave the battery in the rain, nor charge, use, 

or store the battery in a damp or wet place.

 If 

the terminal gets wet or liquid enters inside of bat-

tery, the battery may be short circuited and there is 

a risk of overheat, fire, or explosion.

8. 

After removing the battery from the machine or 

charger, be sure to attach the battery cover to 

the battery and store it in a dry place.

9. 

Do not replace the battery with wet hands.

10. 

If the battery gets wet, drain the water inside 

and then wipe it with a dry cloth. Dry the bat-

tery completely in a dry place before use.

11. 

Avoid dangerous environment. Don't use the 

machine in dump or wet locations or expose it 

to rain.

 Water entering the machine will increase 

the risk of electric shock.

Service

1. 

Have your power tool serviced by a qualified 

repair person using only identical replacement 

parts.

 This will ensure that the safety of the power 

tool is maintained.

2. 

Never service damaged battery packs.

 Service 

of battery packs should only be performed by the 

manufacturer or authorized service providers.

SAVE THESE INSTRUCTIONS.

WARNING:

 

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product.
MISUSE or failure to follow the safety rules stated 

in this instruction manual may cause serious 

personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using 

battery.

2. 

Do not disassemble or tamper the battery 

cartridge.

 It may result in a fire, excessive heat, 

or explosion.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store and use the tool and battery car-

tridge in locations where the temperature may 

reach or exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Do not nail, cut, crush, throw, drop the battery 

cartridge, or hit against a hard object to the 

battery cartridge.

 Such conduct may result in a 

fire, excessive heat, or explosion.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-

aging and labeling must be observed. 

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

Summary of Contents for UB001GZ

















Reviews: