background image

8

ENGLISH

This tool has a reversing switch to change the direction of rota-
tion. Depress the reversing switch lever from the A side for clock-
wise rotation or from the B side for counterclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.

Changing the application mode

Changing the impact force

You can change the impact force in four steps: 4 (max), 3 (hard), 2 (medium), and 1 (soft).
This allows a tightening suitable to the work.

The level of the impact force changes every time you press the button 

.

You can change the impact force within approximately one minute after releasing the switch trigger.

NOTE:

 

You can extend the time to change the impact force approximately one minute if you press the button 

 or 

.

Application mode 

(Impact force grade displayed on panel)

Maximum blows

Purpose

4 (Max)

4,000 min

-1

 (/min)

Tightening with the maximum force and 
speed.
Tightening when the force and the speed 
are desired.

3 (Hard)

3,400 min

-1

 (/min)

Tightening with less force and speed than 
Max mode (easier to control than Max 
mode).
Tightening when the force and the speed 
are desired.

2 (Medium)

2,600 min

-1

 (/min)

Tightening when a good finishing is 

needed.

Tightening when you need good control 

power.

1 (Soft)

1,800 min

-1

 (/min)

Tightening with less force to avoid screw 
thread breakage.

Tightening when you need fine adjustment 

with small diameter bolts.

: The lamp is on.

Summary of Contents for TW004GM201

















Reviews: